P2123: Throttle position sensor switch D circuit high input
DIY difficulty 4/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonThe PCM may enter limp-in mode with acceleration severely limited or disabled, and the throttle can stick.
One of your throttle position sensor circuits is reporting a voltage that is too high - the signal may be shorted to a higher voltage or the sensor may be faulty.
Key facts
P2123 means throttle position sensor switch D circuit high input. One of your throttle position sensor circuits is reporting a voltage that is too high - the signal may be shorted to a higher voltage or the sensor may be faulty. WrenchFair's published fair-price range for this repair is $50–$400 parts and $100–$300 labor at independent shops.
WrenchFair rates P2123 a 4-of-5 DIY difficulty (“Cleaning carbon from the throttle body and inspecting wiring are DIY-friendly; sensor signal testing needs a scanner or multimeter.”) with a “Diagnose soon” driveability rating: The PCM may enter limp-in mode with acceleration severely limited or disabled, and the throttle can stick. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on
stuck throttle (at any rpm)
limited or no acceleration
engine stall when allowed to idle
hesitation when accelerating
cruise control inoperative
Likely causes
Open or shorted circuits between the TPS, PPS, and the PCM
Defective TPS or PPS
Corroded electrical connectors
Carbon buildup holding the throttle body open at startup
Faulty drive-by-wire actuator motor
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 7 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check for technical service bulletins for your vehicle.
Visually inspect all system related wiring and connectors. Tests: Corroded electrical connectors
Check the throttle plate for carbon buildup or damage - excessive buildup that holds the throttle body open can set this code. Tests: Carbon buildup holding the throttle body open at startup
Retrieve all codes and freeze frame data, clear the codes, and test drive.
Monitor TPS and PPS signals with the scanner while slowly actuating the throttle - look for spikes or inconsistencies.
Test sensor signal voltage against manufacturer specifications with the DVOM.
Note: some manufacturers require the throttle body, actuator motor, and all throttle position sensors to be replaced as a single unit.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$50 – $400
Labor$100 – $300
Throttle or pedal position sensor replacement, throttle body cleaning. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2123 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Cleaning carbon from the throttle body and inspecting wiring are DIY-friendly; sensor signal testing needs a scanner or multimeter.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →