P2118: Throttle actuator control motor current range/performance
DIY difficulty 2/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonThrottle faults can trigger limp mode with reduced power. Avoid highways until diagnosed.
The electric throttle motor is drawing abnormal electrical current - either struggling against a jam or barely drawing anything because of a bad connection. The computer limits power while it can't trust the throttle.
VW/Audi note (VCDS): If your tool shows throttle motor duty cycle, excessive duty at idle indicates the motor is fighting a bound blade.
Model notes: Motor current monitoring is how the ECM catches a throttle problem before it becomes dangerous - this code often appears before drivability gets bad.
Key facts
P2118 means throttle actuator control motor current range/performance. The electric throttle motor is drawing abnormal electrical current - either struggling against a jam or barely drawing anything because of a bad connection. The computer limits power while it can't trust the throttle. WrenchFair's published fair-price range for this repair is $10–$250 parts and $80–$250 labor at independent shops.
WrenchFair rates P2118 a 2-of-5 DIY difficulty (“High current usually means mechanical binding (clean it); low current usually means electrical (test it).”) with a “Diagnose soon” driveability rating: Throttle faults can trigger limp mode with reduced power. Avoid highways until diagnosed. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
reduced power mode
sluggish throttle
check engine light
engine will not start
smoke from tailpipe
increased fuel consumption
Likely causes
Carbon-bound throttle blade overloading the motor (most common high-current cause)
Failing motor with shorted windings
Poor connection causing low current
Damaged wiring to the throttle body
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Clean the throttle body first - binding from carbon is the most common high-current cause Tests: Carbon-bound throttle blade overloading the motor (most common high-current cause)
Measure motor winding resistance against spec Tests: Failing motor with shorted windings
Voltage-drop test the power and ground circuits under load
Replace the throttle body if the motor draws wrong current with a clean, free blade Tests: Carbon-bound throttle blade overloading the motor (most common high-current cause)
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$10 – $250
Labor$80 – $250
Cleaning is nearly free; throttle body replacement costs more. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2118 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — High current usually means mechanical binding (clean it); low current usually means electrical (test it).
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →