P210E: Throttle/pedal Position Sensor/switch C/f Voltage Correlation
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonDangerous: loss of throttle control - stalling, no acceleration, or stuck throttle. Diagnose immediately.
The computer sees two conflicting signals about how far open the throttle is, so it does not trust either.
Model notes: On an Infiniti this may read Throttle position sensor circuit range/performance; on a Hyundai Electronic throttle control system malfunction power management.
Key facts
P210E means throttle/pedal Position Sensor/switch C/f Voltage Correlation. The computer sees two conflicting signals about how far open the throttle is, so it does not trust either. WrenchFair's published fair-price range for this repair is $30–$400 parts and $75–$350 labor at independent shops.
WrenchFair rates P210E a 3-of-5 DIY difficulty (“Connector inspection and cleaning are easy; sensor voltage tests and relearn procedures are intermediate; handle throttle body with extreme care.”) with a “Diagnose soon” driveability rating: Dangerous: loss of throttle control - stalling, no acceleration, or stuck throttle. Diagnose immediately. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light illuminated
stalling when coming to a stop
total lack of power
no acceleration
sudden loss of power at cruise speeds
stuck throttle at current rpm
Likely causes
Corroded, bent, or pulled-out female terminals in the throttle body wiring connector (pigtail)
Bare wire on the pigtail shorting to ground
Distorted throttle body top cover preventing the drive gears from turning
Faulty electronic throttle body
Failed accelerator pedal sensor or its wiring
Failed engine management computer
TPS sensors out of correlation; computer needs a relearn procedure or dealer reprogramming
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check technical service bulletins for the vehicle and code; some vehicles have a throttle relearn procedure (e.g., on a Nissan, cycle the ignition and pedal through a prescribed sequence) or require dealer reprogramming. Tests: TPS sensors out of correlation; computer needs a relearn procedure or dealer reprogramming
Pull the electrical connector from the throttle body; inspect closely for missing or bent female terminals and corrosion. Clean corrosion with a small pocket screwdriver, apply electrical grease, and reconnect. Tests: Corroded, bent, or pulled-out female terminals in the throttle body wiring connector…
If terminals are bent or missing, replace the throttle body pigtail with one from an auto parts store or the dealer. Tests: Corroded, bent, or pulled-out female terminals in the throttle body wiring connector…
Inspect the throttle body top cover for cracks or warping; a distorted cover compromises the gears and the whole throttle body must be replaced. Tests: Distorted throttle body top cover preventing the drive gears from turning
With a voltmeter, probe the accelerator pedal sensor: it should have a 5V reference and a varying signal that climbs smoothly from about 0.5 to 5.0 volts as the pedal is depressed. Replace it if the voltage spikes or is absent.
Probe the throttle body connector for power to the throttle motor while a helper turns the key on and slightly depresses the pedal; no power suggests a computer fault, power present with no movement suggests a faulty throttle body.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$30 – $400
Labor$75 – $350
Throttle body or accelerator pedal sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P210E ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Connector inspection and cleaning are easy; sensor voltage tests and relearn procedures are intermediate; handle throttle body with extreme care.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →