Diagnose soonThe vehicle is forced to idle with little or no throttle response - get it towed or repaired.
Your car's computer detected a problem elsewhere and is forcing the engine to idle only as a safety measure - this code is the messenger, not the cause.
Key facts
P2104 means throttle actuator control system forced idle. Your car's computer detected a problem elsewhere and is forcing the engine to idle only as a safety measure - this code is the messenger, not the cause. WrenchFair's published fair-price range for this repair is $100–$500 parts and $100–$400 labor at independent shops.
WrenchFair rates P2104 a 3-of-5 DIY difficulty (“Reading all codes and researching TSBs is DIY-friendly; the underlying fault may need professional diagnosis.”) with a “Diagnose soon” driveability rating: The vehicle is forced to idle with little or no throttle response - get it towed or repaired. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Service bulletins: 413 factory bulletins on file for this vehicle (mostly Electrical System, Equipment, Engine And Engine Cooling) — see the latest ones
On your 2016–2016 Ford Explorer (3.5L Ti-VCT V6, 2.3L EcoBoost I4, 2.0L EcoBoost I4) — Electronic throttle body failure — wrench light and limp mode:Owner-verified
On top of the engine under the plastic cover — four bolts and an electrical connector. Owners call it a 15-minute swap once diagnosed.
Do this test first: Research technical service bulletins for your vehicle and this code.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P2104 on the 2016–2016 Ford Explorer — but the community-sourced Electronic throttle body failure — wrench light and limp mode note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Throttle body mounting bolts: verify — Torque spec not confirmed from a forum source — confirm against factory service info before torquing.
Tips
The pattern: the wrench light comes on and the truck suddenly loses power (limp mode), often with no warning and at low mileage — owners reported it as early as 5,500–10,000 miles. Typical codes are P2112 (throttle stuck closed) and P2104 (forced idle).
Ford's service path was a PCM reflash first, then throttle body replacement when the problem returned. Owners who got only the reflash frequently had the failure come back within days — if your dealer proposes just the reflash, know that the throttle body itself is the likely end of the story.
Root cause per owner investigation: the early ('A' part number) throttle body bore had a lip that collected crankcase oil into a gunk glue holding the plate, combined with a weak plate motor. The plate sticks, the computer sees the position mismatch, and it forces limited power.
Critical practical tip from the thread: if it happens, do NOT shut the engine off — that resets the system and erases the evidence. Drive (or tow) it to the dealer with the fault still active so they can see it.
Parts availability was a real problem during the failure wave — dealers waited weeks for throttle bodies. If yours is failing, get the part ordered before you are stranded. About 60 owner reports at CarComplaints plus 90 at NHTSA document the scope.
Typical difficulty: Moderate — based on 307 code guides for the intake repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
check engine light on
little or no throttle response
engine forced to idle
abs light may be illuminated
automatic transmission may not shift
additional codes present
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Another stored fault the PCM considers safety-related (most common) - see co-occurring codes
Engine overheating or coolant leaks
EGR valve malfunction
Mass airflow sensor malfunction
ABS, traction control, or stability control failure
Automatic transmission problem
Abnormal system voltage
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Research technical service bulletins for your vehicle and this code.
Complete a full PCM scan and list all other stored trouble codes. Tests: Another stored fault the PCM considers safety-related (most common) - see co-occurring…
Diagnose and repair the OTHER codes first - P2104 is informational and set because of them.
Once all other codes are cleared, see if P2104 returns.
If P2104 persists with no other codes, evaluate the throttle actuator and PCM - inspect all wiring and connections.
Do not replace the throttle actuator or PCM before the underlying fault is fixed.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2016–2016 Ford Explorer: Electronic throttle body failure — wrench light and limp mode — test first, then buy for this job.
The price range below is a national planning range for P2104 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$100 – $500
Labor$100 – $400
Varies by underlying cause - often a sensor, connector, or wiring repair. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2104 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Reading all codes and researching TSBs is DIY-friendly; the underlying fault may need professional diagnosis.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →