P20D3: Exhaust aftertreatment fuel injector B control circuit low
DIY difficulty 4/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonThe aftertreatment system may be damaged if the underlying condition is not fixed quickly.
On your diesel, aftertreatment injector B - which sprays diesel exhaust fluid into the exhaust - is sending a low signal. The aftertreatment system could be damaged if this is not fixed.
Key facts
P20D3 means exhaust aftertreatment fuel injector B control circuit low. On your diesel, aftertreatment injector B - which sprays diesel exhaust fluid into the exhaust - is sending a low signal. The aftertreatment system could be damaged if this is not fixed. WrenchFair's published fair-price range for this repair is $150–$600 parts and $150–$400 labor at independent shops.
WrenchFair rates P20D3 a 4-of-5 DIY difficulty (“Checking the DEF level and inspecting wiring is DIY-friendly; activating the injector and testing the circuit needs a capable scanner.”) with a “Diagnose soon” driveability rating: The aftertreatment system may be damaged if the underlying condition is not fixed quickly. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on
diminished engine performance
excessive black smoke from vehicle exhaust
reduction in fuel efficiency
other aftertreatment / scr related codes
Likely causes
Bad exhaust aftertreatment fuel injector B (most common)
Open or shorted circuits in the aftertreatment fuel injection control circuit
Insufficient DEF in the aftertreatment reservoir
Bad EAS controller / PCM or programming error
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 7 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check for technical service bulletins for your vehicle.
Check the DEF level in the aftertreatment reservoir and top up with fresh fluid if low. Tests: Insufficient DEF in the aftertreatment reservoir
Visually inspect the aftertreatment wiring harnesses and connectors - repair burnt or damaged wiring first. Tests: Bad exhaust aftertreatment fuel injector B (most common)
Retrieve all codes and freeze frame data, clear the codes, and test drive.
Test the power supply to the aftertreatment control system and test fuses with the circuit loaded.
Use the scanner to activate the aftertreatment fuel injector and test the output control circuit voltage.
Test the injector against the manufacturer's specifications - do not forget ground circuits when voltage-drop testing.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$150 – $600
Labor$150 – $400
Aftertreatment fuel injector B replacement or wiring repair. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P20D3 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Checking the DEF level and inspecting wiring is DIY-friendly; activating the injector and testing the circuit needs a capable scanner.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →