P2095: B camshaft position actuator control circuit high bank 2
DIY difficulty 4/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonYou can usually drive, but a failed timing chain or belt can cause internal engine damage - do not ignore rough running.
The variable valve timing solenoid circuit for the B camshaft (exhaust camshaft) on bank 2 (the side without cylinder 1) is reading too high - usually a bad VVT solenoid, a short to power in the wiring, or a damaged connector.
Key facts
P2095 means b camshaft position actuator control circuit high bank 2. The variable valve timing solenoid circuit for the B camshaft (exhaust camshaft) on bank 2 (the side without cylinder 1) is reading too high - usually a bad VVT solenoid, a short to power in the wiring, or a damaged connector. WrenchFair's published fair-price range for this repair is $30–$400 parts and $100–$800 labor at independent shops.
WrenchFair rates P2095 a 4-of-5 DIY difficulty (“Checking oil, fuses, and connectors is easy DIY; solenoid replacement is moderate; timing component work needs the factory procedures.”) with a “Diagnose soon” driveability rating: You can usually drive, but a failed timing chain or belt can cause internal engine damage - do not ignore rough running. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Short to power or damaged wiring in the actuator circuit
Defective variable valve timing actuator
Corroded or damaged connector
Engine oil level too low or oil condition too poor
Worn timing belt or chain
Misalignment of timing components
Faulty ECU (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 8 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check for technical service bulletins for your year, model, and engine.
Check the oil level and condition - VVT needs correct oil pressure to work. Tests: Engine oil level too low or oil condition too poor
Check the fuse or fusible link for the VVT circuit if applicable. Tests: Short to power or damaged wiring in the actuator circuit
Locate the bank 2 B camshaft variable timing solenoid and actuator and inspect the wiring for shorts to power, scraping, rubbing, bare wires, and burn spots. Tests: Defective camshaft variable timing solenoid (most common)
Check the connectors for security, corrosion, and damaged pins.
Test the solenoid against the factory specs and replace it if it fails.
Check timing alignment - if this code appeared right after a timing belt or chain replacement, suspect misaligned timing components.
Only suspect the ECU after the solenoid, wiring, timing, and oil are all proven good.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$30 – $400
Labor$100 – $800
VVT solenoid replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2095 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Checking oil, fuses, and connectors is easy DIY; solenoid replacement is moderate; timing component work needs the factory procedures.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →