P2081: Exhaust gas temperature (EGT) sensor circuit intermittent bank 1 sensor 1
DIY difficulty 4/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonYou can usually drive, but intermittent faults tend to become permanent - get it fixed before a long hot run.
The exhaust temperature sensor before the converter on bank 1 (the side with cylinder 1) is dropping out intermittently - usually a loose or corroded connector, chafed wiring, or a sensor failing only when it gets hot.
Key facts
P2081 means exhaust gas temperature (EGT) sensor circuit intermittent bank 1 sensor 1. The exhaust temperature sensor before the converter on bank 1 (the side with cylinder 1) is dropping out intermittently - usually a loose or corroded connector, chafed wiring, or a sensor failing only when it gets hot. WrenchFair's published fair-price range for this repair is $40–$250 parts and $100–$300 labor at independent shops.
WrenchFair rates P2081 a 4-of-5 DIY difficulty (“Inspecting connectors and wiggle-testing the harness is DIY-friendly; intermittent faults are the hardest to pin down.”) with a “Diagnose soon” driveability rating: You can usually drive, but intermittent faults tend to become permanent - get it fixed before a long hot run. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on, sometimes clearing on its own
no other readily recognizable symptoms
Likely causes
Loose or corroded connectors or terminals (most common)
Chafed wiring or missing insulation causing an intermittent short to ground
Aftermarket catless exhaust without EGT provisions
Faulty PCM (unlikely)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 7 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check for technical service bulletins for your make and model.
Locate the bank 1 sensor 1 EGT sensor - between the exhaust manifold and the converter, or before the DPF on a diesel. Tests: Aftermarket catless exhaust without EGT provisions
Check the connectors and pigtail for corrosion, loose terminals, and missing insulation or bare wires. Tests: Loose or corroded connectors or terminals (most common)
Wiggle-test the harness while watching live EGT data for dropouts.
Remove the sensor and test its resistance against the factory spec, including when fully hot.
Heat the sensor with a hair dryer or heat gun while watching the ohmmeter - resistance should drop as it heats and rise as it cools.
Replace the sensor if it fails the resistance or response test.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$40 – $250
Labor$100 – $300
EGT sensor replacement or wiring repair. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2081 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Inspecting connectors and wiggle-testing the harness is DIY-friendly; intermittent faults are the hardest to pin down.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →