Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonYou can drive, but the fuel gauge cannot be trusted - refuel often and track mileage until it is fixed.
The secondary fuel gauge sender (B circuit) is reading too high - usually a wire shorted to battery voltage, a bad tank ground, or an open in the sender resistor. The gauge may read full or fluctuate.
Key facts
P2068 means fuel level sensor B circuit high input. The secondary fuel gauge sender (B circuit) is reading too high - usually a wire shorted to battery voltage, a bad tank ground, or an open in the sender resistor. The gauge may read full or fluctuate. WrenchFair's published fair-price range for this repair is $50–$400 parts and $200–$600 labor at independent shops.
WrenchFair rates P2068 a 3-of-5 DIY difficulty (“Ground-strap and connector inspection are easy; replacing the sender means dropping the tank or removing the pump module, which is a bigger job.”) with a “Diagnose soon” driveability rating: You can drive, but the fuel gauge cannot be trusted - refuel often and track mileage until it is fixed. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on
fuel level gauge may fluctuate abnormally or read empty or full
fuel light may illuminate and sound alarm
Likely causes
Signal circuit to the fuel sender shorted to battery voltage (most common)
Ground circuit open, or high resistance from rust or a missing ground strap on the fuel tank
Open in the fuel level sensor resistor to ground
Damage to the fuel tank from impact
Faulty instrument cluster (possible)
PCM, BCM, or fuel pump computer module failure (unlikely)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 7 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check for technical service bulletins for your make and model.
Visually inspect the fuel tank and wiring harness for impact damage, missing ground strap, or a rusty ground. Tests: Ground circuit open, or high resistance from rust or a missing ground strap on the fuel…
Inspect the wiring harness connector at the tank for damage and repair as needed. Tests: Damage to the fuel tank from impact
Verify that reference voltage is present at the fuel level sensor at the fuel pump wiring harness; if not, repair the open or short. Tests: Open in the fuel level sensor resistor to ground
Do a voltage drop test on the ground circuit - ideally 0.1 volts or less; anything near 1 volt indicates a ground problem.
Provide a good ground to the sensor at the tank connector with the key on - the gauge should swing to one extreme; if it responds, the wiring and cluster are good and the sender is the suspect.
If the sender is the problem, replace the fuel level sensor (may require replacing the fuel pump module).
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$50 – $400
Labor$200 – $600
Fuel level sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2068 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Ground-strap and connector inspection are easy; replacing the sender means dropping the tank or removing the pump module, which is a bigger job.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →