P2023

P2023: Intake manifold runner position sensor/switch circuit intermittent (bank 2)

DIY difficulty 3/5

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.

The sensor that reports where the little air-shaping flaps inside your intake are sitting keeps cutting in and out on the non-cylinder-1 side. Intermittent usually means a loose or corroded connection, or flaps sticking from carbon buildup. Expect the light to come and go, with occasional weak power or misfires.

Key facts

Symptoms

Likely causes

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 6 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Check for technical service bulletins for your make and model, and diagnose any other intake or engine-performance codes first - they can set this one as a side effect. Tests: Sticking throttle plates or vacuum/intake leaks upsetting the readings - fix those codes…
  2. Confirm there are no intake or vacuum leaks, which can skew the readings. Tests: Sticking throttle plates or vacuum/intake leaks upsetting the readings - fix those codes…
  3. Inspect the bank 2 IMRC connector and wiring for rubbing, bare wires, melted plastic, and corroded terminals; clean, pack with dielectric compound, reassemble, clear the code, and retest. Tests: Loose, corroded, or intermittently connecting terminals in the bank 2 IMRC sensor…
  4. Watch the IMRC sensor signal on a scan tool while snapping the throttle - the signal should change smoothly with RPM per the factory chart. Tests: Loose, corroded, or intermittently connecting terminals in the bank 2 IMRC sensor…
  5. Remove the IMRC sensor/actuator and move the flap linkage by hand (watch for a strong return spring) to check for binding or looseness.
  6. If the flaps move freely but the signal is still erratic, replace the sensor/actuator; if the plates bind, the intake manifold usually needs replacement.

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Typical price range

Parts$30 – $600
Labor$150 – $600

IMRC sensor or solenoid replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2023 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

3 of 5 — Intermittent faults are the hardest to catch; start with connectors and a wiggle test, and expect possible intake manifold removal if the flaps are binding.

Watch this repair on YouTube

Parts & tools

Intake & throttle toolkit — what the job actually takes

Torque specs: Throttle body bolts: typically 8–12 Nm — verify spec.

Pro tip: Some cars need a throttle relearn after cleaning (scan tool or battery-disconnect procedure), or the idle will hunt.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →