P2023: Intake manifold runner position sensor/switch circuit intermittent (bank 2)
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonSafe to drive, but an intermittent flap problem can turn into a stuck one - fix it while it is still just annoying.
The sensor that reports where the little air-shaping flaps inside your intake are sitting keeps cutting in and out on the non-cylinder-1 side. Intermittent usually means a loose or corroded connection, or flaps sticking from carbon buildup. Expect the light to come and go, with occasional weak power or misfires.
Key facts
P2023 means intake manifold runner position sensor/switch circuit intermittent (bank 2). The sensor that reports where the little air-shaping flaps inside your intake are sitting keeps cutting in and out on the non-cylinder-1 side. Intermittent usually means a loose or corroded connection, or flaps sticking from carbon buildup. Expect the light to come and go, with occasional weak power or misfires. WrenchFair's published fair-price range for this repair is $30–$600 parts and $150–$600 labor at independent shops.
WrenchFair rates P2023 a 3-of-5 DIY difficulty (“Intermittent faults are the hardest to catch; start with connectors and a wiggle test, and expect possible intake manifold removal if the flaps are binding.”) with a “Diagnose soon” driveability rating: Safe to drive, but an intermittent flap problem can turn into a stuck one - fix it while it is still just annoying. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on, may come and go
lack of power
occasional misfire
poor fuel economy
Likely causes
Loose, corroded, or intermittently connecting terminals in the bank 2 IMRC sensor connector (most common - inspect and clean first)
IMRC runner flaps sticking or binding from carbon deposits around them
IMRC vacuum solenoid failing to vent properly from carbon in its vent port
Faulty bank 2 IMRC actuator/sensor
Sticking throttle plates or vacuum/intake leaks upsetting the readings - fix those codes first
Failed PCM (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check for technical service bulletins for your make and model, and diagnose any other intake or engine-performance codes first - they can set this one as a side effect. Tests: Sticking throttle plates or vacuum/intake leaks upsetting the readings - fix those codes…
Confirm there are no intake or vacuum leaks, which can skew the readings. Tests: Sticking throttle plates or vacuum/intake leaks upsetting the readings - fix those codes…
Inspect the bank 2 IMRC connector and wiring for rubbing, bare wires, melted plastic, and corroded terminals; clean, pack with dielectric compound, reassemble, clear the code, and retest. Tests: Loose, corroded, or intermittently connecting terminals in the bank 2 IMRC sensor…
Watch the IMRC sensor signal on a scan tool while snapping the throttle - the signal should change smoothly with RPM per the factory chart. Tests: Loose, corroded, or intermittently connecting terminals in the bank 2 IMRC sensor…
Remove the IMRC sensor/actuator and move the flap linkage by hand (watch for a strong return spring) to check for binding or looseness.
If the flaps move freely but the signal is still erratic, replace the sensor/actuator; if the plates bind, the intake manifold usually needs replacement.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$30 – $600
Labor$150 – $600
IMRC sensor or solenoid replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2023 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Intermittent faults are the hardest to catch; start with connectors and a wiggle test, and expect possible intake manifold removal if the flaps are binding.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →