P2019: Intake manifold runner position sensor/switch circuit (bank 2)
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonSafe to drive, but you will feel weak power and burn more fuel - and a wrong position reading can mask a real mechanical flap problem.
A sensor that tells the computer where the little air-shaping flaps inside your intake are sitting is giving a bad or missing signal on the non-cylinder-1 side. Could be the sensor, carbon-stuck flaps, or wiring. Expect the check engine light, weak power, and worse mileage.
Key facts
P2019 means intake manifold runner position sensor/switch circuit (bank 2). A sensor that tells the computer where the little air-shaping flaps inside your intake are sitting is giving a bad or missing signal on the non-cylinder-1 side. Could be the sensor, carbon-stuck flaps, or wiring. Expect the check engine light, weak power, and worse mileage. WrenchFair's published fair-price range for this repair is $30–$600 parts and $150–$600 labor at independent shops.
WrenchFair rates P2019 a 3-of-5 DIY difficulty (“Connector inspection and cleaning is easy; signal testing needs a multimeter and the factory wiring diagram, and a binding flap check can require intake manifold removal.”) with a “Diagnose soon” driveability rating: Safe to drive, but you will feel weak power and burn more fuel - and a wrong position reading can mask a real mechanical flap problem. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on
lack of power
occasional misfire
poor fuel economy
Likely causes
Corroded, burnt, or loose terminals in the bank 2 IMRC sensor connector (most common - inspect and clean first)
Sticking or faulty bank 2 IMRC valve from carbon deposits around the flaps
Faulty bank 2 IMRC actuator/sensor
Chafed, rubbed, or melted wiring in the sensor circuit
Sticking throttle plates or intake/vacuum leaks setting companion codes - diagnose those first
Failed PCM (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check for technical service bulletins for your make and model, and diagnose any other intake or engine-performance codes first - they can set this one as a side effect. Tests: Sticking throttle plates or intake/vacuum leaks setting companion codes - diagnose those…
Confirm there are no intake or vacuum leaks, which can skew the readings. Tests: Sticking throttle plates or intake/vacuum leaks setting companion codes - diagnose those…
Locate the bank 2 IMRC valve/sensor, inspect the connector and wiring for chafing, bare wires, burn spots, and corroded terminals; clean, pack with dielectric compound, reassemble, clear the code, and retest. Tests: Corroded, burnt, or loose terminals in the bank 2 IMRC sensor connector (most common -…
Watch the IMRC sensor signal on a scan tool while snapping the throttle - the signal should change smoothly with RPM per the factory chart. Tests: Corroded, burnt, or loose terminals in the bank 2 IMRC sensor connector (most common -…
Remove the IMRC sensor/actuator and move the flap linkage by hand (watch for a strong return spring) to check for binding or looseness.
If the flaps move freely but the signal is still bad, replace the sensor/actuator; if the plates bind, the intake manifold usually needs replacement.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$30 – $600
Labor$150 – $600
IMRC position sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2019 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Connector inspection and cleaning is easy; signal testing needs a multimeter and the factory wiring diagram, and a binding flap check can require intake manifold removal.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →