P2015

P2015: Intake Manifold Runner Position Sensor/switch Circuit Range/performance Bank 1

For your specific vehicle: P2015 on a 2009–2017 Volkswagen Tiguan

DIY difficulty 3/5

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.

The bank 1 intake runner position sensor is sending a signal that is out of range or does not match what the computer expects.

Model notes: Very common on VW 2.0T engines (Jetta, Passat CC, Tiguan, Audi A4) where the intake manifold runner flaps and sensor wear. Also seen on Ford, Dodge, Toyota, Mercedes, Nissan, Infiniti.

Key facts

Symptoms

Likely causes

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 7 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Check technical service bulletins for the vehicle in question.
  2. Diagnose any other stored intake or engine performance codes first; an intake leak makes the engine run lean and an exhaust leak skews the AFR/O2 sensor reading. Tests: Intake or exhaust leak skewing the runner position signal
  3. Locate the IMRC valve/sensor, visually inspect connectors and wiring for rubbing, bare wires, or melted plastic. Tests: Damaged, corroded, or chafed wiring or connectors in the IMRC sensor circuit
  4. Pull connectors apart and inspect terminals for burnt or corroded metal; clean with electrical contact cleaner, air dry, pack with dielectric silicone compound, and reassemble. Tests: Damaged, corroded, or chafed wiring or connectors in the IMRC sensor circuit
  5. Clear the codes and see if the code returns; if not, the connection was likely the problem.
  6. If it returns, monitor IMRC sensor voltage on the scan tool while snapping the throttle; signal should change smoothly as RPM increases.
  7. If the signal fails to respond, remove the sensor/actuator and turn the runner linkage by hand to check for binding or looseness; some runner flaps are not replaceable separately and intake manifold replacement may be needed (a job better left to professionals).

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Typical price range

Parts$60 – $400
Labor$75 – $450

IMRC actuator/sensor or intake manifold replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2015 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

3 of 5 — Wiring inspection and connector cleaning are easy; runner binding checks and intake manifold removal are advanced.

Watch this repair on YouTube

Parts & tools

Intake & throttle toolkit — what the job actually takes

Torque specs: Throttle body bolts: typically 8–12 Nm — verify spec.

Pro tip: Some cars need a throttle relearn after cleaning (scan tool or battery-disconnect procedure), or the idle will hunt.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →