Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonPower loss and occasional misfire; diagnose before driveability worsens.
The bank 1 intake runner position sensor is sending a signal that is out of range or does not match what the computer expects.
Model notes: Very common on VW 2.0T engines (Jetta, Passat CC, Tiguan, Audi A4) where the intake manifold runner flaps and sensor wear. Also seen on Ford, Dodge, Toyota, Mercedes, Nissan, Infiniti.
Key facts
P2015 means intake Manifold Runner Position Sensor/switch Circuit Range/performance Bank 1. The bank 1 intake runner position sensor is sending a signal that is out of range or does not match what the computer expects. WrenchFair's published fair-price range for this repair is $60–$400 parts and $75–$450 labor at independent shops.
WrenchFair rates P2015 a 3-of-5 DIY difficulty (“Wiring inspection and connector cleaning are easy; runner binding checks and intake manifold removal are advanced.”) with a “Diagnose soon” driveability rating: Power loss and occasional misfire; diagnose before driveability worsens. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
malfunction indicator lamp (MIL) illuminated
lack of power
occasional misfire
poor fuel economy
Likely causes
Sticking or faulty intake manifold runner valve
Faulty IMRC actuator/sensor
Sticking or faulty throttle plates/body
Intake or exhaust leak skewing the runner position signal
Damaged, corroded, or chafed wiring or connectors in the IMRC sensor circuit
Faulty powertrain control module (PCM) (rare; requires programming after replacement)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 7 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check technical service bulletins for the vehicle in question.
Diagnose any other stored intake or engine performance codes first; an intake leak makes the engine run lean and an exhaust leak skews the AFR/O2 sensor reading. Tests: Intake or exhaust leak skewing the runner position signal
Locate the IMRC valve/sensor, visually inspect connectors and wiring for rubbing, bare wires, or melted plastic. Tests: Damaged, corroded, or chafed wiring or connectors in the IMRC sensor circuit
Pull connectors apart and inspect terminals for burnt or corroded metal; clean with electrical contact cleaner, air dry, pack with dielectric silicone compound, and reassemble. Tests: Damaged, corroded, or chafed wiring or connectors in the IMRC sensor circuit
Clear the codes and see if the code returns; if not, the connection was likely the problem.
If it returns, monitor IMRC sensor voltage on the scan tool while snapping the throttle; signal should change smoothly as RPM increases.
If the signal fails to respond, remove the sensor/actuator and turn the runner linkage by hand to check for binding or looseness; some runner flaps are not replaceable separately and intake manifold replacement may be needed (a job better left to professionals).
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$60 – $400
Labor$75 – $450
IMRC actuator/sensor or intake manifold replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2015 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Wiring inspection and connector cleaning are easy; runner binding checks and intake manifold removal are advanced.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →