P2014: Intake Manifold Runner Position Sensor/switch Circuit Bank 1
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonPower loss and occasional misfire; diagnose before driveability worsens.
The computer cannot read the position signal from the intake runner flaps on bank 1.
Model notes: Applies to Ford, Dodge, Toyota, Mercedes, Nissan, Infiniti. Subaru uses tumble generator valves (TGV) for this function.
Key facts
P2014 means intake Manifold Runner Position Sensor/switch Circuit Bank 1. The computer cannot read the position signal from the intake runner flaps on bank 1. WrenchFair's published fair-price range for this repair is $60–$300 parts and $75–$400 labor at independent shops.
WrenchFair rates P2014 a 3-of-5 DIY difficulty (“Wiring inspection and connector cleaning are easy; runner binding checks and intake manifold removal are advanced.”) with a “Diagnose soon” driveability rating: Power loss and occasional misfire; diagnose before driveability worsens. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
malfunction indicator lamp (MIL) illuminated
lack of power
occasional misfire
poor fuel economy
Likely causes
Sticking or faulty intake manifold runner valve
Faulty IMRC actuator/sensor
Sticking or faulty throttle plates/body
Intake or exhaust leak affecting the runner position signal
Damaged, corroded, or chafed wiring or connectors in the IMRC sensor circuit
Faulty powertrain control module (PCM) (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 7 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check technical service bulletins for the vehicle in question.
Diagnose any other stored intake or engine performance codes first; an intake leak makes the engine run lean and an exhaust leak skews the AFR/O2 sensor reading. Tests: Intake or exhaust leak affecting the runner position signal
Locate the IMRC valve/sensor, visually inspect connectors and wiring for chafing, rubbing, bare wires, burn spots, or melted plastic. Tests: Damaged, corroded, or chafed wiring or connectors in the IMRC sensor circuit
Pull connectors apart and inspect terminals for corrosion or burnt/green metal; clean with electrical contact cleaner and protect with dielectric silicone compound. Tests: Damaged, corroded, or chafed wiring or connectors in the IMRC sensor circuit
Clear the codes and see if the code returns; if not, the connection was likely the problem.
If it returns, monitor IMRC sensor voltage on the scan tool while snapping the throttle; signal should change as RPM increases.
If the signal does not respond, verify the runner plates move freely by removing the sensor/actuator and turning the linkage by hand; binding or excessive looseness may require replacing the intake manifold (a job better left to professionals).
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$60 – $300
Labor$75 – $400
IMRC actuator/sensor replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2014 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Wiring inspection and connector cleaning are easy; runner binding checks and intake manifold removal are advanced.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →