P2012: Intake manifold runner control circuit low (bank 2)
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonSafe to drive, but hesitation on acceleration is a real drivability problem - fix it before it strands you at a bad merge.
The wiring that controls the little air-shaping flaps inside your intake is reading too low a voltage on the non-cylinder-1 side - think short circuit, corroded connector, or a dying control valve. The car runs but hesitates and uses more fuel.
Key facts
P2012 means intake manifold runner control circuit low (bank 2). The wiring that controls the little air-shaping flaps inside your intake is reading too low a voltage on the non-cylinder-1 side - think short circuit, corroded connector, or a dying control valve. The car runs but hesitates and uses more fuel. WrenchFair's published fair-price range for this repair is $40–$400 parts and $150–$450 labor at independent shops.
WrenchFair rates P2012 a 3-of-5 DIY difficulty (“The circuit checks need a multimeter and the factory wiring diagram; reaching the actuator and linkage often means removing intake components.”) with a “Diagnose soon” driveability rating: Safe to drive, but hesitation on acceleration is a real drivability problem - fix it before it strands you at a bad merge. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on
hesitation upon acceleration
reduction in engine performance, especially at low rpm
rich or lean exhaust
diminished fuel efficiency
engine surge
Likely causes
Corroded IMRC actuator connector face causing low voltage in the circuit (most common)
Shorted wiring in the bank 2 IMRC actuator solenoid control circuit
Defective bank 2 IMRC actuator solenoid
Binding or loose intake manifold runners loading down the actuator
Bad bank 2 IMRC runner position sensor
Carbon buildup on the IMRC flaps or intake manifold ports
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check for technical service bulletins for your make and model - several have known IMRC fixes.
Inspect the bank 2 IMRC actuator connector face for corrosion, bent pins, and poor fit - this is the most common cause of a low-voltage reading. Tests: Corroded IMRC actuator connector face causing low voltage in the circuit (most common)
Test the actuator solenoid and position sensor resistance against the factory specs and replace whichever fails. Tests: Shorted wiring in the bank 2 IMRC actuator solenoid control circuit
With the controllers disconnected to avoid damage, check the control circuit for shorts to ground and excessive resistance. Tests: Shorted wiring in the bank 2 IMRC actuator solenoid control circuit
Disconnect the actuator from the linkage shaft and move the runner flaps by hand to rule out mechanical binding.
Clear the code, test drive, and confirm the circuit voltage now behaves normally before returning the vehicle to service.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$40 – $400
Labor$150 – $450
Connector repair or IMRC actuator replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P2012 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — The circuit checks need a multimeter and the factory wiring diagram; reaching the actuator and linkage often means removing intake components.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →