P200D: Diesel particulate filter over temperature (bank 2)
DIY difficulty 4/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonAddress this promptly - an overheating DPF can cook the catalyst and turn a sensor or DEF problem into a multi-thousand-dollar exhaust replacement.
Your diesel soot filter is getting hotter than it should on the non-cylinder-1 side. That usually means the exhaust-fluid system that controls regeneration is not doing its job, or a temperature sensor is lying. This one deserves prompt attention - sustained overheating can destroy the expensive filter and catalyst.
Key facts
P200D means diesel particulate filter over temperature (bank 2). Your diesel soot filter is getting hotter than it should on the non-cylinder-1 side. That usually means the exhaust-fluid system that controls regeneration is not doing its job, or a temperature sensor is lying. This one deserves prompt attention - sustained overheating can destroy the expensive filter and catalyst. WrenchFair's published fair-price range for this repair is $60–$3000 parts and $150–$600 labor at independent shops.
WrenchFair rates P200D a 4-of-5 DIY difficulty (“Checking DEF and sensors is DIY-friendly, but verifying actual DPF temperatures against sensor data takes an infrared thermometer and a scan tool - and a melted-down DPF is a shop job.”) with a “Diagnose soon” driveability rating: Address this promptly - an overheating DPF can cook the catalyst and turn a sensor or DEF problem into a multi-thousand-dollar exhaust replacement. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light on
diminished engine performance
excessive black smoke from the exhaust
reduction in fuel efficiency
other emission-related codes stored
Likely causes
Incorrect or insufficient diesel exhaust fluid (most common - check the DEF tank first)
Faulty SCR injector over- or under-dosing the exhaust
Defective exhaust temperature sensor giving bad readings
Inoperative SCR system or bad SCR controller
Exhaust leak ahead of the catalyst
Aftermarket or high-performance exhaust components upsetting temperatures
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
If any SCR codes are stored, diagnose those first; repair any exhaust leaks ahead of the catalyst before anything else. Tests: Exhaust leak ahead of the catalyst
Check for technical service bulletins for your make and model.
Confirm the DEF reservoir is full of the correct fluid and the SCR system is actually injecting.
Visually inspect the SCR injector, exhaust temperature sensors, NOx sensors, and oxygen sensor wiring and connectors for burnt or damaged wiring. Tests: Defective exhaust temperature sensor giving bad readings
Use an infrared thermometer to measure actual pre- and post-DPF temperatures and compare them to the scanner data and between banks.
Test any sensor that disagrees with the thermometer against the factory specs; if all sensors and wiring check out, suspect the DPF itself or a failed SCR system.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$60 – $3000
Labor$150 – $600
Exhaust temperature sensor or SCR injector replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P200D ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Checking DEF and sensors is DIY-friendly, but verifying actual DPF temperatures against sensor data takes an infrared thermometer and a scan tool - and a melted-down DPF is a shop job.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →