P0EF4: Drive Motor C Temperature Sensor Circuit High
DIY difficulty 4/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonExpect reduced power or limp mode; get it diagnosed before any long drive.
The drive motor temperature sensor signal is stuck high - think of a wire touching a power feed or a failed sensor. Expect reduced power or limp mode.
Key facts
P0EF4 means drive Motor C Temperature Sensor Circuit High. The drive motor temperature sensor signal is stuck high - think of a wire touching a power feed or a failed sensor. Expect reduced power or limp mode. WrenchFair's published fair-price range for this repair is $230–$1720 parts and $140–$900 labor at independent shops.
WrenchFair rates P0EF4 a 4-of-5 DIY difficulty (“High-voltage system: lethal voltage in the pack and orange cables - pack and inverter internals are qualified-technician-only work, and DIY is limited to visual checks, fuses, and 12V-side testing.”) with a “Diagnose soon” driveability rating: Expect reduced power or limp mode; get it diagnosed before any long drive. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
ev/hybrid system warning light on
reduced motor power or torque
possible limp mode or vehicle shutdown
Likely causes
signal wire shorted to B+ (most common)
open sensor
connector pins corroded - high contact resistance
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
1. HIGH-VOLTAGE SAFETY FIRST: this code touches the traction-battery high-voltage system. Lethal voltage lives in the pack and the orange cables - pack internals are qualified-technician-only work. DIY is limited to visual inspection, fuses, and 12V-side checks with the system depowered.
2. Clear the code and confirm it returns under the same conditions before replacing anything.
3. Inspect the drive motor c temperature sensor connector and wiring for damage, corrosion, water intrusion, or pins pushed back out of the connector body - pay attention to spots where the harness flexes or rubs. Tests: connector pins corroded - high contact resistance
4. With a scan tool, watch the live drive motor c temperature sensor reading while wiggling the harness; a reading that jumps or drops out confirms a wiring or connector fault. Tests: connector pins corroded - high contact resistance
5. Check the drive motor c temperature sensor power, ground, and signal wiring for opens and shorts per the factory service manual before condemning the part.
6. If the wiring tests good, replace the drive motor c temperature sensor or component, then retest.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$230 – $1720
Labor$140 – $900
Repairing the short in the drive motor c temperature sensor circuit. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0EF4 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — High-voltage system: lethal voltage in the pack and orange cables - pack and inverter internals are qualified-technician-only work, and DIY is limited to visual checks, fuses, and 12V-side testing.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →