P0C1C: Electric/auxiliary transmission fluid pump control module internal temperature sensor circuit
DIY difficulty 4/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonExpect reduced power or limp mode — the hybrid system protects itself by limiting the electric side. Drive gently to a shop and skip long trips.
This sensor is a thermometer for part of the hybrid system, there so the computer can tell if things are getting too hot. This code means the computer no longer trusts its readings (an electrical problem in the wiring), so it's blind to overheating in that spot. The sensor area can sit near high-voltage hardware, so visual checks are fine but keep your hands off anything you can't positively identify as low-voltage.
Key facts
P0C1C means electric/auxiliary transmission fluid pump control module internal temperature sensor circuit. This sensor is a thermometer for part of the hybrid system, there so the computer can tell if things are getting too hot. This code means the computer no longer trusts its readings (an electrical problem in the wiring), so it's blind to overheating in that spot. The sensor area can sit near high-voltage hardware, so visual checks are fine but keep your hands off anything you can't positively identify as low-voltage. WrenchFair's published fair-price range for this repair is $125–$1500 parts and $300–$1200 labor at independent shops.
WrenchFair rates P0C1C a 4-of-5 DIY difficulty (“Mostly a shop job: you can check the 12V battery, fuses, and accessible connectors, but high-voltage diagnosis is technician-only.”) with a “Diagnose soon” driveability rating: Expect reduced power or limp mode — the hybrid system protects itself by limiting the electric side. Drive gently to a shop and skip long trips. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine or transmission warning light on
harsh, delayed, or missing shifts
possible limp mode (locked in one gear)
slipping or shuddering during gear changes
Likely causes
sensor failed
internal module fault
sensor connector corroded or loose
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Park, power down completely, and respect the high-voltage system: the battery pack and orange cables are lethal to touch. Leave anything inside the pack to a trained technician; you can safely check the 12V battery, fuses, and connectors outside the pack. Tests: sensor connector corroded or loose
Check the 12V battery's health and terminal connections — a weak 12V battery is a classic cause of phantom hybrid codes.
Check the coolant level in the relevant reservoir — low coolant or trapped air skews temperature readings.
Inspect the sensor's connector for corrosion, loose pins, or coolant contamination. Tests: sensor connector corroded or loose
With a scanner that reads hybrid live data, compare this sensor to the other temperature sensors after the car sits overnight — they should all read near the outside air temperature.
A sensor stuck at one value or jumping wildly usually needs replacement, which sits near HV hardware — get a quote.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$125 – $1500
Labor$300 – $1200
sensor failed. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0C1C ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Mostly a shop job: you can check the 12V battery, fuses, and accessible connectors, but high-voltage diagnosis is technician-only.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →