P0B35: High voltage service disconnect circuit low
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonThe car may refuse to enter ready mode or shut down without warning — plan on a tow rather than forcing a drive.
Every high-voltage connector in the car is part of a safety loop: open any connector and the loop breaks, cutting the high voltage. This code means that safety loop looks broken to the computer, which usually means a connector isn't fully seated or a cable is damaged. The loop exists because the voltage involved can kill, so have a trained technician confirm it before forcing anything.
Key facts
P0B35 means high voltage service disconnect circuit low. Every high-voltage connector in the car is part of a safety loop: open any connector and the loop breaks, cutting the high voltage. This code means that safety loop looks broken to the computer, which usually means a connector isn't fully seated or a cable is damaged. The loop exists because the voltage involved can kill, so have a trained technician confirm it before forcing anything. WrenchFair's published fair-price range for this repair is $50–$300 parts and $75–$450 labor at independent shops.
WrenchFair rates P0B35 a 3-of-5 DIY difficulty (“Middle of the road: visual checks, connectors, fuses, and 12V tests are DIY-friendly, but anything on the high-voltage side belongs to a technician.”) with a “Diagnose soon” driveability rating: The car may refuse to enter ready mode or shut down without warning — plan on a tow rather than forcing a drive. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
vehicle won't enter ready mode
hybrid system warning light on
no-start after recent service work
Likely causes
wire shorted to ground
switch shorted
connector pins corroded - high contact resistance
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Park, power down completely, and respect the high-voltage system: the battery pack and orange cables are lethal to touch. Leave anything inside the pack to a trained technician; you can safely check the 12V battery, fuses, and connectors outside the pack. Tests: connector pins corroded - high contact resistance
Check that the service plug and any interlock connectors you can see are fully seated — look, don't force, and never remove the service plug while the car is powered. Tests: connector pins corroded - high contact resistance
Inspect visible orange-cable connectors for damage or unlatched locking tabs. Do not disconnect them. Tests: connector pins corroded - high contact resistance
Think about recent work: a connector left unlatched after service is the classic cause. Tests: connector pins corroded - high contact resistance
If everything looks seated, the break is inside a connector or cable — technician diagnosis from here.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$50 – $300
Labor$75 – $450
wire shorted to ground. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0B35 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Middle of the road: visual checks, connectors, fuses, and 12V tests are DIY-friendly, but anything on the high-voltage side belongs to a technician.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →