P0971: Pressure control solenoid C control circuit high
DIY difficulty 4/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonMaxed line pressure bangs every shift - diagnose it before the drivetrain takes the beating.
The wire controlling your transmission's third pressure solenoid is stuck high - pressure is maxed out. Expect harsh, slamming shifts.
Key facts
P0971 means pressure control solenoid C control circuit high. The wire controlling your transmission's third pressure solenoid is stuck high - pressure is maxed out. Expect harsh, slamming shifts. WrenchFair's published fair-price range for this repair is $60–$400 parts and $150–$600 labor at independent shops.
WrenchFair rates P0971 a 4-of-5 DIY difficulty (“Harsh slamming shifts are the telltale sign of this fault.”) with a “Diagnose soon” driveability rating: Maxed line pressure bangs every shift - diagnose it before the drivetrain takes the beating. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
harsh, slamming shifts
hard engagement into gear
limp mode
Likely causes
Solenoid C control wire shorted to battery voltage (most common)
Shorted pressure control solenoid C internally
Damaged connector with pins bridged to a power wire
Chafed internal transmission harness
Failed PCM/TCM driver (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check fluid level and condition first.
Scan all codes and note the shift behavior - maxed pressure means harsh engagement. Tests: Shorted pressure control solenoid C internally
Inspect the harness for chafing where the control wire could touch a 12V feed. Tests: Solenoid C control wire shorted to battery voltage (most common)
Test the circuit for a short to power with the meter.
Disconnect the solenoid and retest to isolate the short.
Repair wiring or replace the solenoid; pan removal is usually required for access.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$60 – $400
Labor$150 – $600
Pressure control solenoid C circuit short repair (solenoid replacement if failed). National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0971 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Harsh slamming shifts are the telltale sign of this fault.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →