P084A: Transmission fluid pressure sensor/switch H circuit
DIY difficulty 4/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonThe computer is shifting without a good pressure reading on this circuit - limp mode is likely, so diagnose it soon.
Another transmission pressure sensor (the 'H' one) has an electrical fault. Expect changed shift feel and possibly limp mode.
Key facts
P084A means transmission fluid pressure sensor/switch H circuit. Another transmission pressure sensor (the 'H' one) has an electrical fault. Expect changed shift feel and possibly limp mode. WrenchFair's published fair-price range for this repair is $80–$350 parts and $200–$500 labor at independent shops.
WrenchFair rates P084A a 4-of-5 DIY difficulty (“Connector inspection is easy; the sensor itself is often inside the pan on the valve body.”) with a “Diagnose soon” driveability rating: The computer is shifting without a good pressure reading on this circuit - limp mode is likely, so diagnose it soon. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
changed shift quality - harsh or soft shifts
transmission starts in 2nd or 3rd gear (limp mode)
check-engine light on
Likely causes
Corroded or damaged external connector at the transmission (most common)
Failed transmission fluid pressure sensor/switch H
Open, shorted, or chafed wiring in the sensor circuit
Internal transmission problems - leaks, stuck valve, low line pressure
Failed PCM/TCM (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check for TSBs and companion power or pressure codes - diagnose power faults and multi-sensor codes first. Tests: Failed transmission fluid pressure sensor/switch H
Check fluid level and condition; burnt fluid or debris points to internal problems. Tests: Internal transmission problems - leaks, stuck valve, low line pressure
Locate the TFPS 'H' and inspect its connector and wiring for corrosion, rubbing, and burn spots - external connector corrosion is the most common cause. Tests: Corroded or damaged external connector at the transmission (most common)
Clear the code after cleaning the connector; if it returns, test circuit power, ground, and signal. Tests: Corroded or damaged external connector at the transmission (most common)
Test the sensor against factory specs; replace it if it fails.
If sensor and circuit test good, suspect internal leaks, a stuck valve, or low line pressure.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$80 – $350
Labor$200 – $500
Transmission fluid pressure sensor/switch replacement (often requires pan removal). National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P084A ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — Connector inspection is easy; the sensor itself is often inside the pan on the valve body.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →