Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Drive safeA switch B high fault costs you cruise control, not drivability - fix it when convenient.
Your second clutch switch is reading too high - usually a shorted wire or bad ground. Expect cruise control to refuse to engage and a check-engine light.
Key facts
P0835 means clutch pedal switch B circuit high. Your second clutch switch is reading too high - usually a shorted wire or bad ground. Expect cruise control to refuse to engage and a check-engine light. WrenchFair's published fair-price range for this repair is $25–$120 parts and $80–$200 labor at independent shops.
WrenchFair rates P0835 a 2-of-5 DIY difficulty (“Same under-dash circuit as the other switch codes - follow the wiring diagram to the fault.”) with a “Drive safe” driveability rating: A switch B high fault costs you cruise control, not drivability - fix it when convenient. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
cruise control will not engage
check-engine light on
no starting problems
Likely causes
Signal wire shorted to battery voltage (most common)
Open or corroded ground in the switch B circuit
Failed clutch pedal switch B stuck in the high state
Switch B misadjusted on the pedal bracket
Failed PCM (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Look up TSBs for the year, make, and model matching this code.
Inspect the harness for chafing where the signal wire could touch a 12V feed; check connectors for bridged pins. Tests: Signal wire shorted to battery voltage (most common)
Test the switch ground for continuity - an open ground drives the signal high. Tests: Open or corroded ground in the switch B circuit
Disconnect switch B and see if the high signal drops; replace the switch if it is the source. Tests: Failed clutch pedal switch B stuck in the high state
Check switch B adjustment on the pedal bracket.
Clear the code and verify clean switching through the full pedal travel.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$25 – $120
Labor$80 – $200
Clutch pedal switch B replacement or wiring short repair. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0835 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Same under-dash circuit as the other switch codes - follow the wiring diagram to the fault.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →