Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonAny fault that can let the engine start in gear is a safety issue - verify the starter interlock works before driving.
Your car's computer thinks the clutch pedal is in the wrong place for what the car is doing. Usually a bad pedal sensor or its wiring - on an automatic transmission, it points at the computer instead.
Key facts
P0810 means clutch position control error. Your car's computer thinks the clutch pedal is in the wrong place for what the car is doing. Usually a bad pedal sensor or its wiring - on an automatic transmission, it points at the computer instead. WrenchFair's published fair-price range for this repair is $25–$150 parts and $80–$200 labor at independent shops.
WrenchFair rates P0810 a 2-of-5 DIY difficulty (“Same pedal-switch territory as the P0805 family - inspect, test, and adjust before replacing anything.”) with a “Diagnose soon” driveability rating: Any fault that can let the engine start in gear is a safety issue - verify the starter interlock works before driving. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
starter will not engage
engine starts with the transmission in gear
no symptoms besides the check-engine light
Likely causes
Failed clutch position/pedal sensor (most common on manuals)
Open or shorted wiring or connector in the clutch position control circuit
Clutch pedal switch out of adjustment
On automatics: PCM/TCM failure or programming error
Faulty control module (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Note the transmission type: on an automatic, skip to module and programming checks. Tests: On automatics: PCM/TCM failure or programming error
Look up TSBs for the year, make, and model matching this code.
Watch the clutch position input on scan-tool live data while working the pedal; compare against actual pedal position. Tests: Failed clutch position/pedal sensor (most common on manuals)
Inspect the pedal switch adjustment, mounting, wiring, and connectors for damage or corrosion. Tests: Clutch pedal switch out of adjustment
Test sensor output and circuit voltage/ground per the factory chart; adjust or replace the sensor as needed.
On automatics, verify module power/grounds and check for available software updates before condemning the module.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$25 – $150
Labor$80 – $200
Clutch position sensor replacement or circuit repair. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0810 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Same pedal-switch territory as the P0805 family - inspect, test, and adjust before replacing anything.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →