Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonLimp mode is protective - diagnose before driving far.
Your transmission picks gears with electric shift valves, and solenoid G is faulty. Expect wrong or missing gears, or limp mode. Check the fluid level first, then test the solenoid.
Key facts
P075A means shift Solenoid G. Your transmission picks gears with electric shift valves, and solenoid G is faulty. Expect wrong or missing gears, or limp mode. Check the fluid level first, then test the solenoid. WrenchFair's published fair-price range for this repair is $60–$400 parts and $200–$500 labor at independent shops.
WrenchFair rates P075A a 3-of-5 DIY difficulty (“Solenoids are in the pan on the valve body; a fluid and filter service is often done at the same time.”) with a “Diagnose soon” driveability rating: Limp mode is protective - diagnose before driving far. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
wrong gear
missing gears
limp mode
harsh shifts
check engine light on
Likely causes
failed shift solenoid G
low or contaminated fluid
wiring fault
valve body fault
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check the fluid level and condition.
Scan for all codes and record freeze-frame data, then clear the code and test-drive to see if it returns.
Test solenoid G's resistance. Tests: failed shift solenoid G
Inspect the wiring. Replace the solenoid if it tests bad. Tests: failed shift solenoid G
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$60 – $400
Labor$200 – $500
Shift solenoid G replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P075A ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Solenoids are in the pan on the valve body; a fluid and filter service is often done at the same time.
Torque specs: Pan bolts: typically 8–12 Nm in a crisscross pattern — verify spec. Over-tightening warps the pan and causes leaks.
Pro tip: Use ONLY the fluid your transmission calls for (e.g. ZF Lifeguard 8 for ZF 8-speeds) — wrong fluid kills transmissions. Measure what came out.
As an Amazon Associate, WrenchFair earns from qualifying purchases.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →