Diagnose soonExpect limp mode with limited gears - drive gently to a shop.
The transmission's output speed sensor has gone completely silent. Harsh shifts and limp mode are likely.
Model notes: Check the wiring to the sensor before replacing it - the harness runs near hot exhaust and chafes.
Key facts
P0722 means output speed sensor circuit no signal. The transmission's output speed sensor has gone completely silent. Harsh shifts and limp mode are likely. WrenchFair's published fair-price range for this repair is $40–$150 parts and $200–$500 labor at independent shops.
WrenchFair rates P0722 a 3-of-5 DIY difficulty (“See P0715.”) with a “Diagnose soon” driveability rating: Expect limp mode with limited gears - drive gently to a shop. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2008–2014 Mercedes-Benz C-Class (all) — 7G-Tronic 722.9 conductor plate / speed-sensor failure:Owner-verified
The conductor plate lives on the valve body inside the transmission pan - pan off, filter out, valve body down, plate unbolts from the valve body. The whole job happens from underneath the car.
Do this test first: Compare output speed to wheel speed in live data
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0722 on the 2008–2014 Mercedes-Benz C-Class — but the community-sourced 7G-Tronic 722.9 conductor plate / speed-sensor failure note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Valve body / conductor plate: verify — No valve-body torque values confirmed from a forum source - confirm against factory service info before torquing.
Tips
The classic signature is the transmission dropping into limp mode (stuck in one gear, rough shifts) with speed-sensor codes - P0717 and P0722 are the common pair. Restarting the car may clear it temporarily, which is itself a clue.
If fluid and filter changes have been neglected, a conductor plate fault can hide behind old fluid - but a proper transmission scan pointing at the speed sensors is the confirmation, and guessing at a full valve body first wastes money.
A repaired or refurbished plate is a recognized option that costs less than new, and a refurbished original does not need coding the way a brand-new plate does - worth knowing since the new part requires dealer-level programming.
Replace the electrical connector and service the fluid and filter while the pan is off, since the whole job is already open.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
harsh shifting
speedometer issues
limp mode
poor fuel economy
engine feels like it is misfiring
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Failed output speed sensor
Damaged tone wheel
Wiring fault
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 1 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Compare output speed to wheel speed in live data Tests: Failed output speed sensor
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2008–2014 Mercedes-Benz C-Class: 7G-Tronic 722.9 conductor plate / speed-sensor failure — test first, then buy for this job.
The price range below is a national planning range for P0722 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$40 – $150
Labor$200 – $500
Sensor replacement; pan removal labor on many transmissions. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0722 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →