Diagnose soonA bad sensor reading can cause poor running or stalling. Drive carefully and diagnose soon.
The sensor measuring how fast the transmission's input shaft spins has gone silent. The transmission can't verify its gears, so it shifts harshly or goes into limp mode.
Model notes: Input and output speed sensors often fail together with age - if one is dead, test the other while you are diagnosing.
Key facts
P0717 means input/turbine speed sensor circuit no signal. The sensor measuring how fast the transmission's input shaft spins has gone silent. The transmission can't verify its gears, so it shifts harshly or goes into limp mode. WrenchFair's published fair-price range for this repair is $30–$120 parts and $80–$200 labor at independent shops.
WrenchFair rates P0717 a 3-of-5 DIY difficulty (“Many input sensors are inside the transmission - external ones are an easy swap.”) with a “Diagnose soon” driveability rating: A bad sensor reading can cause poor running or stalling. Drive carefully and diagnose soon. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2007–2009 GMC Acadia (3.6L V6) — 3-5-R wave plate failure (no reverse, 3rd/5th flare):Owner-verified
Transmission-out job — the 3-5-R clutch wave plate lives inside the 6T70/6T75 case. Diagnosis is the DIY-friendly part; the repair is a transmission rebuild or replacement best left to a specialist.
Do this test first: Check transmission fluid level first - low fluid causes all manner of sensor codes
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0717 on the 2007–2009 GMC Acadia — but the community-sourced 3-5-R wave plate failure (no reverse, 3rd/5th flare) note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Transmission internal fasteners: verify — Specialist rebuild — no owner-documented torque specs; confirm against factory service info.
Tips
Learn the pattern: SES light plus no reverse, and/or a slip/flare or harsh shift in 3rd and 5th gears. The classic DTC is P0776 (clutch pressure control solenoid 2 stuck off); P0777, P2723, P0717, P0716, P2715, and P2714 can set from the same failure.
The cause per GM bulletin 09-07-30-012B is a broken 3-5-R (35R) clutch wave plate that lets the apply piston over-stroke and leak — typically not before about 20,000 miles. Debris from the breakage can also foul the speed sensors and other clutches.
The documented fix is the updated waved clutch plate (P/N 24254103) with a full cleanup: debris cleaned from the whole transmission, plus a new pump fluid filter and control-solenoid filter plate. Skipping the cleanup is how repeat failures happen.
One owner caught it early and had a dealer rebuild for under $1,500 with GM assistance — so stop driving it the moment reverse disappears or 3rd/5th starts flaring, and call a dealer about goodwill help before authorizing a $4,000-$5,000 replacement.
If a shop does the rebuild, the plate's installation orientation matters (GM guidance: rounded edge of the internal splines toward the 35R piston) to prevent a repeat failure.
A full replacement transmission is the common outcome once debris has circulated — multiple owners report reman units after the wave plate disintegrated, so early diagnosis genuinely saves money here.
Typical difficulty: Moderate — based on 306 code guides for the transmission repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
harsh shifting
limp mode (stuck in one gear)
check engine light
speedometer or odometer stops working
worse fuel mileage
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Failed input speed sensor (most common) 3 owner notes link this repair to P0717
Damaged wiring or connector
Damaged tone ring
Low transmission fluid affecting sensor reading (check level) 3 owner notes link this repair to P0717
Owner notes linked to P0717: 3 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check transmission fluid level first - low fluid causes all manner of sensor codes Tests: Low transmission fluid affecting sensor reading (check level)
Watch the input speed PID - zero while the engine runs confirms the fault Tests: Failed input speed sensor (most common)
Test the sensor and its wiring where accessible
On internal sensors, the repair may require pan or valve body removal
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2007–2009 GMC Acadia: 3-5-R wave plate failure (no reverse, 3rd/5th flare) — test first, then buy for this job.
The price range below is a national planning range for P0717 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$30 – $120
Labor$80 – $200
Sensor replacement is the typical fix. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0717 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Many input sensors are inside the transmission - external ones are an easy swap.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →