P0524

P0524 on a 2008–2012 Infiniti G37: Engine Oil Pressure Too Low

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.
For your specific vehicle: P0524 on a 2016–2018 Chevrolet Camaro · 2008–2012 Infiniti G37 · 2016–2016 Nissan Titan

DIY difficulty 5/5

STOP. Your engine's oil pressure is genuinely too low, and driving even a short distance can destroy the engine. Pull over safely right now, turn the engine off, and have it towed. This is not a 'drive to the shop' code - bearings and camshafts die in minutes without oil pressure.

Key facts

☑ Before you buy parts — check these first:
On your 2008–2012 Infiniti G37 (3.7L VQ37VHR V6) — VQ37VHR oil gallery gaskets: low hot-idle oil pressure, P0011/P0021, VTC rattle: Owner-verified
Timing-cover-off job on the front of the engine. Confirm the diagnosis first with a mechanical oil-pressure gauge at the stock sender location: a healthy VQ37VHR shows roughly 20+ psi at hot idle; a failed gallery gasket reads low at idle and stays low under load while the OEM low-pressure light stays off.
Do this test first: Pull over safely and shut the engine OFF immediately.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0524 on the 2008–2012 Infiniti G37 — but the community-sourced VQ37VHR oil gallery gaskets: low hot-idle oil pressure, P0011/P0021, VTC rattle note above covers an owner-reported fix.
Fixed yours? Report it — you'll help the next owner.

Torque specs

Tips

Sources: myg37.com 'P0021 P0011 VVT Solenoid' - G37 owner replaced the rear timing cover (gallery) gasket, confirmed oil pressure good afterward (26.5 psi at idle at 80C oil temp); P0021 persisted until the faulty bank 2 intake timing solenoid was also fixed · myg37.com 'P0011, P0021, P0524, p0075, p0081, p0340, p0345 check before replacing gasket' - documents the gallery gasket vs VTC phaser slip-ring differential diagnosis on the G37; FSM possible causes: oil pressure/level too low, cam/crank sensors, intake valve control solenoid, timing chain installation, debris on signal pick-up

Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

No owner reports yet

Symptoms

Likely causes

What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.

Owner notes linked to P0524: 3 across 2 repairs — these are counts of owner-written notes, not odds of fixing your car.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 3 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Pull over safely and shut the engine OFF immediately.
  2. Check the oil level only after the engine is off - do not restart it.
  3. Have the car towed to a shop for mechanical oil pressure testing and diagnosis.

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Most likely job on your 2008–2012 Infiniti G37: VQ37VHR oil gallery gaskets: low hot-idle oil pressure, P0011/P0021, VTC rattle — test first, then buy for this job.
The price range below is a national planning range for P0524 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers.
If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.

Typical price range

Parts$200 – $3000
Labor$300 – $1500

Oil pump replacement or engine repair after pressure loss. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0524 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

5 of 5 — Professional diagnosis required - do not run the engine.

Watch this repair on YouTube

Parts & tools

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →