Diagnose soonA bad sensor reading can cause poor running or stalling. Drive carefully and diagnose soon.
The sensor that tells your car how fast it's going has failed. Expect a dead speedometer, no cruise control, and harsh transmission shifting all at the same time.
Model notes: A dead speedometer plus shifting complaints is the classic combination - both come from the same missing speed signal. On many vehicles the transmission uses its own internal speed sensors, so shifting may be unaffected.
Key facts
P0500 means vehicle speed sensor A circuit malfunction. The sensor that tells your car how fast it's going has failed. Expect a dead speedometer, no cruise control, and harsh transmission shifting all at the same time. WrenchFair's published fair-price range for this repair is $30–$120 parts and $80–$200 labor at independent shops.
WrenchFair rates P0500 a 2-of-5 DIY difficulty (“Usually one bolt and a connector; the sensor is often on the transmission housing.”) with a “Diagnose soon” driveability rating: A bad sensor reading can cause poor running or stalling. Drive carefully and diagnose soon. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Service bulletins: 388 factory bulletins on file for this vehicle (mostly Electrical System, Equipment, Power Train) — see the latest ones
On your 2013–2019 Nissan Sentra (1.8L (MR18DE), CVT (JF015E)) — Wheel bearing (hub assembly) replacement:Owner-verified
Bolt-on hub assembly, no press needed. After the wheel is off, remove the caliper and bracket, then the rotor. Undo the 32mm axle nut, unplug the ABS sensor, and unbolt the four hub bolts from the back of the steering knuckle. The hub usually separates by hand once unbolted — but rust-belt cars seize the hub into the knuckle, and owners resort to penetrating oil, hammer blows, and air chisels. A tie-rod puller helps free the axle from the hub splines without hammering on the axle itself.
Do this test first: Watch the vehicle speed PID on the scan tool while driving - no signal confirms the fault
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0500 on the 2013–2019 Nissan Sentra — but the community-sourced Wheel bearing (hub assembly) replacement note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Axle nut: verify — Confirm against factory service info before torquing — critical for bearing preload.
Hub-to-knuckle bolts: verify — Confirm against factory service info for the B17.
Tips
Classic diagnosis: a roaring or 'airplane' noise above ~40 mph that changes or disappears when you turn left or right — turning shifts load onto/off of the bad bearing.
The ABS sensor connector gets brittle with age; handle it gently and don't yank the wiring — an ABS/traction light after the job (C0035) almost always means the sensor or its wiring got damaged during the swap.
Don't reuse the axle nut; stake or torque the new one properly and never hammer directly on the CV axle end or you'll wreck the threads.
Check both sides — when one hub fails from mileage, the other often isn't far behind.
Typical difficulty: Moderate — based on 265 code guides for the brake repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
speedometer dead or erratic
cruise control inoperative
harsh or wrong transmission shifts
ABS light may come on
odometer stops counting miles
rev limiter engages at lower rpm
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Failed vehicle speed sensor (most common)
Damaged wiring or connector, often from road debris
Damaged tone ring or reluctor the sensor reads
Failed sensor drive gear (on transmission-mounted designs)
Owner notes linked to P0500: 3 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 4 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Watch the vehicle speed PID on the scan tool while driving - no signal confirms the fault Tests: Failed vehicle speed sensor (most common)
Inspect the sensor, its wiring, and the tone ring for damage Tests: Damaged tone ring or reluctor the sensor reads
Check for related ABS codes that can narrow down which wheel or sensor is involved
Replace the sensor if the circuit is intact but produces no signal
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2013–2019 Nissan Sentra: Wheel bearing (hub assembly) replacement — test first, then buy for this job.
The price range below is a national planning range for P0500 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$30 – $120
Labor$80 – $200
Sensor replacement is the typical fix. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0500 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Usually one bolt and a connector; the sensor is often on the transmission housing.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →