Yes, if your state or county runs an OBD-II emissions test and the check-engine light is on. The test plugs into your car's computer, and under the EPA's OBD inspection criteria any code that commands the light on is itself a failure — no tailpipe reading needed.
Fixing the fault is only half the job. Clearing the code resets every readiness monitor, and they have to run again before the car will pass. The EVAP monitor is often the last to set — it only runs under specific conditions — so don't clear codes the week of your test. See the drive-cycle and readiness guide →
One break for EVAP codes: the EVAP monitor is the single monitor California excuses on 2000-and-newer gasoline vehicles, and in states following the EPA's allowance (up to two monitors not ready for 1996–2000, one for 2001 and newer) it can be your one allowed incomplete monitor. But that excuses an incomplete monitor, not a lit light — while this code is active and the light is on, the car still fails.
Not everywhere tests: some states have no emissions test at all (South Carolina is one), and in others only certain counties test — so there, this code alone won't block registration. Rules vary by county as well as state, and they change, so confirm with your state's DMV before test day.
Tiny leak in the fuel vapor system - too small to see. A smoke test finds it; start with a new gas cap.
Model notes: Replace the gas cap as the cheap first step, then smoke-test if the code returns.
Key facts
P0456 means evaporative emission control system leak detected (very small leak). Tiny leak in the fuel vapor system - too small to see. A smoke test finds it; start with a new gas cap. WrenchFair's published fair-price range for this repair is $15–$80 parts and $80–$200 labor at independent shops.
WrenchFair rates P0456 a 2-of-5 DIY difficulty (“The smoke machine does the work.”) with a “Drive safe” driveability rating: Emissions-only fault. Safe to drive. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Service bulletins: 434 factory bulletins on file for this vehicle (mostly Electrical System, Equipment, Power Train) — see the latest ones
Emissions warranty: P0456 is emissions-related — federal law requires up to 8 years / 80,000 miles of coverage on the catalytic converter, engine computer and OBD system. Check if your repair might be free before you pay for it.
On your 2013–2019 Ford Escape (1.6L EcoBoost, 2.0L EcoBoost) — EVAP purge valve replacement:Owner-verified
The purge valve sits on the driver's side of the engine bay at the front of the engine — on the 1.6L owners reach it after removing the air cleaner assembly. It comes as a valve-plus-hose assembly (Ford CV6Z-9D289-T for the 1.6L, CV6Z-9D289-S for the 2.0L — confirm by VIN, as build time matters). Disconnect the electrical connector, pop the quick-connect vapor lines off, and swap the assembly. One owner caution: don't replace just the solenoid body if the hoses are the updated part — match the whole assembly.
Do this test first: Smoke test - pressurize slightly and watch for wisps
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0456 on the 2013–2019 Ford Escape — but the community-sourced EVAP purge valve replacement note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Purge valve mounting: verify — Plastic quick-connect assembly — no torque fasteners. Confirm part number against VIN before ordering.
Tips
Classic symptom: hard starting or stalling right after filling the tank — a purge valve stuck open floods the engine with raw fuel vapor.
Test the old valve before replacing: remove it and blow through it — you should NOT be able to blow through a good closed valve.
Stop topping off the tank after the pump clicks — repeatedly cramming extra fuel in soaks the charcoal canister and kills purge valves early; owners flag this as the #1 repeat cause.
If P1450/P144C persists after a valve swap, suspect a fuel-soaked charcoal canister or the fuel tank pressure sensor — a smoke test finds the remaining leak.
Clear the codes after the repair and drive normally; EVAP monitors take several drive cycles to self-check, so the light won't clear instantly.
Typical difficulty: Moderate — based on 483 code guides for the fuel repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
check engine light
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Seeping gas cap seal - replace the cap first, it's the cheapest fix
Pinhole in EVAP hose
Vent valve seal/module - Nissan: vent O-ring per TSB NTB17-082; Chrysler/Jeep: ESIM module 9 owner notes link this repair to P0456
Filler-neck sealing-surface rust 9 owner notes link this repair to P0456
Owner notes linked to P0456: 9 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 2 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Smoke test - pressurize slightly and watch for wisps
Replace the gas cap as the cheap first step Tests: Seeping gas cap seal - replace the cap first, it's the cheapest fix
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2013–2019 Ford Escape: EVAP purge valve replacement — test first, then buy for this job.
The price range below is a national planning range for P0456 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$15 – $80
Labor$80 – $200
Gas cap first; a smoke test plus small hose/valve runs more. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0456 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →