DIY difficulty 3/5
| What it means | The catalytic converter on your engine's second bank isn't working efficiently. Same advice as P0420: check for exhaust leaks and bad sensors before buying a cat. |
|---|---|
| Most common cause | Exhaust leak bank 2 |
| Can you drive? | Short trips and gentle driving only, until you know the cause. |
| Severity | Moderate |
| DIY cost (parts only) | $150 – $4000 |
| Shop cost (parts + labor) | $300 – $4500 |
| DIY difficulty | 3 of 5 — Same as P0420. |
Short trips and gentle driving only, until you know the cause. Drivable, but get it diagnosed. If the check-engine light is flashing or you have severe power loss, stop driving. If the check-engine light starts flashing, the engine shakes badly, or the car loses significant power, pull over safely and have it towed.
Moderate. WrenchFair rates this one “Diagnose soon” — the car can usually get you home, but driving on it can turn a cheap fix into an expensive one. Drivable, but get it diagnosed. If the check-engine light is flashing or you have severe power loss, stop driving.
The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.
Yes, if your state or county runs an OBD-II emissions test and the check-engine light is on. The test plugs into your car's computer, and under the EPA's OBD inspection criteria any code that commands the light on is itself a failure — no tailpipe reading needed.
Fixing the fault is only half the job. Clearing the code resets every readiness monitor, and the catalyst monitor has to run clean before the car will pass — a fresh repair with an unset catalyst monitor still fails the readiness check. Drive the car through a full drive cycle first: drive-cycle and readiness guide →
The allowance is small, and it never covers the catalyst monitor. Most states follow the EPA's rule — 1996–2000 vehicles may have up to two monitors not ready, 2001 and newer just one — and California is stricter still for 2000-and-newer gasoline vehicles, where only the EVAP monitor may be incomplete. The catalyst monitor must read ready.
Not everywhere tests: some states have no emissions test at all (South Carolina is one), and in others only certain counties test — so there, this code alone won't block registration. Rules vary by county as well as state, and they change, so confirm with your state's DMV before test day.
The catalytic converter on your engine's second bank isn't working efficiently. Same advice as P0420: check for exhaust leaks and bad sensors before buying a cat.
Owner notes linked to P0430: 7 across 4 repairs — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Work these checks before spending money — each one rules a cause in or out, cheapest first.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Three paths, very different prices: O2 sensor or exhaust gasket $150-$600 installed; aftermarket (EPA) catalytic converter $500-$1,500 installed (real shop invoice: $742 parts + $295 labor = $1,187); OEM or dealer catalytic converter $1,500-$4,000+ — in California and CARB-rule states aftermarket cats are not legal, so budget OEM-only (~$1,800+ at a dealer for common models). The ranges above span all paths; match the tier to your situation. National-average estimate. Actual quotes vary by vehicle, region, and shop — get a local written estimate. Corrected 2026-10-09 against real-world price evidence (Phase 2 adversarial audit).
Before you pay: a catalytic converter replacement can be covered under the federal 8-year/80,000-mile emissions warranty — check your car first.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
Got a shop quote? Grade it →
Torque specs: Exhaust flange nuts: typically 35–50 Nm — verify spec. O2 sensors: typically 35–50 Nm.
Pro tip: A new cat on an engine that’s burning oil or misfiring will die fast — fix the underlying cause first or you’ll be buying another one.
As an Amazon Associate, WrenchFair earns from qualifying purchases.