Diagnose soonLong cranking or no-start is likely; if the engine runs, drive gently to a shop.
Can I drive with P0340?
Can I drive with a P0340 code?
Short trips and gentle driving only, until you know the cause. Long cranking or no-start is likely; if the engine runs, drive gently to a shop. If the check-engine light starts flashing, the engine shakes badly, or the car loses significant power, pull over safely and have it towed.
How serious is P0340?
Moderate. WrenchFair rates this one “Diagnose soon” — the car can usually get you home, but driving on it can turn a cheap fix into an expensive one. Long cranking or no-start is likely; if the engine runs, drive gently to a shop.
Will P0340 go away on its own?
The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.
The sensor that tells the computer where the camshaft is has no signal. Expect long cranking or no-start - but it's usually just the sensor.
Model notes: If P0340 appears with P0016 (crank/cam correlation), suspect timing components, not the sensor.
Key facts
P0340 means camshaft position sensor A circuit malfunction (bank 1). The sensor that tells the computer where the camshaft is has no signal. Expect long cranking or no-start - but it's usually just the sensor. WrenchFair's published fair-price range for this repair is $30–$120 parts and $80–$200 labor at independent shops.
WrenchFair rates P0340 a 2-of-5 DIY difficulty (“Sensor swap is easy; timing diagnosis is not.”) with a “Diagnose soon” driveability rating: Long cranking or no-start is likely; if the engine runs, drive gently to a shop. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
On your 2003–2008 Nissan 350Z (3.5L VQ35DE V6, 3.5L VQ35HR V6) — Camshaft/crankshaft position sensors: the classic stall-and-no-start fix (P0340/P0335):Owner-verified
All three sensors are single-bolt, accessible from under or beside the engine. Check connectors and wiring first - corroded plugs cause the same codes. A basic scan tool confirms the code before you buy parts.
Do this test first: Check sensor supply voltage and ground
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0340 on the 2003–2008 Nissan 350Z — but the community-sourced Camshaft/crankshaft position sensors: the classic stall-and-no-start fix (P0340/P0335) note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Sensor mounting bolt: verify — Sensor is a single small bolt; torque spec not confirmed from a forum source - snug to factory service info, do not overtighten.
Tips
P0340 = bank 1 (passenger side) camshaft position sensor, P0345 = bank 2 (driver side) camshaft sensor, P0335 = crankshaft position sensor. A failed crank sensor often kills the car outright.
Symptoms: engine stalls without warning, long crank, no-start, revs jumping wildly, sudden limp-mode behavior with the MIL on.
Inspect the connector and wiring for corrosion and damage before replacing - sensor wiring shares power splices with other sensors.
The sensors are cheap and the job is simple (one bolt + connector each); many owners carry a spare crank sensor in the glovebox.
If a new sensor does not clear the code, check mechanical timing - stretched timing chains can set cam/crank correlation codes too.
Typical difficulty: Moderate — based on 841 code guides for the sensors repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
long crank
no start
check engine light
loss of VVT
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Failed cam sensor 7 owner notes link this repair to P0340
Damaged tone wheel / reluctor
Wiring fault
Stretched timing chain throwing correlation (see P0016) 7 owner notes link this repair to P0340
Owner notes linked to P0340: 12 across 3 repairs — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 2 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check sensor supply voltage and ground
Scope the signal if equipped; compare to crank signal
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2003–2008 Nissan 350Z: Camshaft/crankshaft position sensors: the classic stall-and-no-start fix (P0340/P0335) — test first, then buy for this job.
The price range below is a national planning range for P0340 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$30 – $120
Labor$80 – $200
Sensor swap is typical; timing diagnosis costs more. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0340 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Sensor swap is easy; timing diagnosis is not.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →