Diagnose soonLong cranking or no-start is likely; if the engine runs, drive gently to a shop.
Can I drive with P0340?
Can I drive with a P0340 code?
Short trips and gentle driving only, until you know the cause. Long cranking or no-start is likely; if the engine runs, drive gently to a shop. If the check-engine light starts flashing, the engine shakes badly, or the car loses significant power, pull over safely and have it towed.
How serious is P0340?
Moderate. WrenchFair rates this one “Diagnose soon” — the car can usually get you home, but driving on it can turn a cheap fix into an expensive one. Long cranking or no-start is likely; if the engine runs, drive gently to a shop.
Will P0340 go away on its own?
The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.
The sensor that tells the computer where the camshaft is has no signal. Expect long cranking or no-start - but it's usually just the sensor.
Model notes: If P0340 appears with P0016 (crank/cam correlation), suspect timing components, not the sensor.
Key facts
P0340 means camshaft position sensor A circuit malfunction (bank 1). The sensor that tells the computer where the camshaft is has no signal. Expect long cranking or no-start - but it's usually just the sensor. WrenchFair's published fair-price range for this repair is $30–$120 parts and $80–$200 labor at independent shops.
WrenchFair rates P0340 a 2-of-5 DIY difficulty (“Sensor swap is easy; timing diagnosis is not.”) with a “Diagnose soon” driveability rating: Long cranking or no-start is likely; if the engine runs, drive gently to a shop. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Service bulletins: 2,692 factory bulletins on file for this vehicle (mostly Equipment, Electrical System, Engine And Engine Cooling) — see the latest ones
On your 2010–2017 Chevrolet Equinox (2.4L Ecotec I4) — Timing chain stretch / cold-start rattle:Owner-verified
Timing cover at the front of the engine — valve cover comes off first. The balance shaft chain sits behind the timing chain and gets serviced at the same time.
Do this test first: Check sensor supply voltage and ground
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for P0340 on the 2010–2017 Chevrolet Equinox — but the community-sourced Timing chain stretch / cold-start rattle note above covers an owner-reported fix. Fixed yours? Report it — you'll help the next owner.
Torque specs
Timing components: verify — Torque specs for chain guides, tensioners, and cover not confirmed from a forum source — confirm against factory service info before torquing.
Tips
The signature symptom is a loud rattle or tick from the front/top of the engine on cold start after sitting 6+ hours, sometimes with rough idle, stalling, or hard starting. It starts as a 1-2 second clack and grows — owners report eventual cam-timing codes (P0016, P0017, P0010, P0011, P0340, P0341) as the stretched chain drifts timing far enough.
Before opening anything, rule out the easy impostors: a forum walkthrough recommends the screwdriver-as-stethoscope test down by the water pump, alternator, and serpentine belt tensioner — a failed water pump or tensioner can sound similar. With the cam cover off, a visibly slack chain confirms stretch.
The community-proven fix is the full set, not the chain alone: timing chain, balance shaft chain, guides, tensioners, and the VVT phasers if they are noisy on startup. Owner-documented kit numbers from DIY videos: Cloyes 9-4201SAVVT1 (timing set) and 9-4202SA (balance chain set); Melling 5499GMB or Dorman 917-954 for the access plug/guide combo.
The VVT phasers are oil-operated and known to clatter for the first seconds on startup as they wear — the same teardown covers them. If you find plastic debris from worn guides, check the phaser solenoid screens for junk; clogged screens throw P0011/P0014 over-advance codes that look like a sensor problem.
Prevention consensus across the threads: frequent full-synthetic oil changes — the chain tensioners are oil-fed, and degraded or low oil is what lets the chain go slack between starts. Check the oil level first on any rattle complaint; these engines are often found low.
Typical difficulty: Moderate — based on 85 code guides for the engine repair area (an area-level estimate, not this exact job).
How notes are verified:Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.
No owner reports yet
Symptoms
long crank
no start
check engine light
loss of VVT
Likely causes
What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.
Failed cam sensor 7 owner notes link this repair to P0340
Damaged tone wheel / reluctor
Wiring fault
Stretched timing chain throwing correlation (see P0016) 7 owner notes link this repair to P0340
Owner notes linked to P0340: 12 across 3 repairs — these are counts of owner-written notes, not odds of fixing your car.
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 2 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check sensor supply voltage and ground
Scope the signal if equipped; compare to crank signal
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Most likely job on your 2010–2017 Chevrolet Equinox: Timing chain stretch / cold-start rattle — test first, then buy for this job.
The price range below is a national planning range for P0340 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers. If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.
Typical price range
Parts$30 – $120
Labor$80 – $200
Sensor swap is typical; timing diagnosis costs more. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0340 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Sensor swap is easy; timing diagnosis is not.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →