P0158

P0158: O2 sensor circuit high voltage, bank 2 sensor 2

DIY difficulty 2/5

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.

Can I drive with P0158?

Can I drive with a P0158 code?

Yes. P0158 doesn't make your car unsafe to drive on its own. Usually just a monitoring fault - but verify fuel trims to rule out real rich running. Fix it when convenient rather than putting it off indefinitely — even a minor fault can turn into a bigger bill if the underlying cause gets worse.

How serious is P0158?

Low. WrenchFair rates this one “Drive safe” — the least serious of its three driveability ratings. It's a fix-on-your-schedule fault, not a same-day emergency. Usually just a monitoring fault - but verify fuel trims to rule out real rich running.

Will P0158 go away on its own?

The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.

Your bank-2 rear oxygen sensor is stuck reading rich - usually a bad sensor, but rule out a real rich-running condition.

Key facts

Symptoms

Likely causes

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 4 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Check fuel trims for a real rich condition Tests: Genuine rich condition
  2. Watch the sensor voltage - stuck high suggests a dead sensor Tests: Failed downstream O2 sensor stuck rich (most common)
  3. Check the wiring for shorts to voltage Tests: Wiring short to voltage
  4. Replace the sensor if the mixture is actually fine

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Typical price range

Parts$40 – $130
Labor$80 – $160

Downstream oxygen sensor replacement (bank 2 sensor 2). National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0158 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

2 of 5 — Check fuel trims to see if the rich condition is real before replacing the sensor.

Watch this repair on YouTube

Parts & tools

Sensor replacement toolkit — what the job actually takes

Torque specs: O2 sensors: typically 35–50 Nm (26–37 lb-ft) — verify spec. A dab of nickel anti-seize on the threads; keep it off the sensor tip.

Pro tip: Route the new sensor’s harness exactly like the old one — melted wires on the exhaust are the number-one comeback.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →