Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Drive safeCatalyst monitoring only - no driveability impact. Fix before your next emissions test.
Your rear oxygen sensor (after the catalytic converter) is getting sluggish with age. It can't properly watch the catalytic converter anymore.
Model notes: Don't confuse with upstream slow response (P0133) - the downstream sensor is supposed to be slow, just not this slow.
Key facts
P013A means o2 sensor slow response, bank 1 sensor 2. Your rear oxygen sensor (after the catalytic converter) is getting sluggish with age. It can't properly watch the catalytic converter anymore. WrenchFair's published fair-price range for this repair is $40–$130 parts and $80–$160 labor at independent shops.
WrenchFair rates P013A a 2-of-5 DIY difficulty (“Watch the sensor's switching speed on a scan tool - a lazy sensor flatlines instead of waving.”) with a “Drive safe” driveability rating: Catalyst monitoring only - no driveability impact. Fix before your next emissions test. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light
no driveability symptoms
possible failed emissions test
Likely causes
Aging/lazy downstream O2 sensor (most common)
Contaminated sensor (coolant, silicone, or oil)
Weak sensor heater
Exhaust leak near the sensor diluting the sample
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Watch the downstream sensor's voltage on a scan tool - it should wave gently, not flatline or race Tests: Aging/lazy downstream O2 sensor (most common)
Check for exhaust leaks near the sensor Tests: Exhaust leak near the sensor diluting the sample
Verify the sensor heater is working (a cold sensor is a slow sensor) Tests: Weak sensor heater
Check for contamination sources (coolant loss, silicone sealant use) Tests: Contaminated sensor (coolant, silicone, or oil)
Replace the sensor if it's lazy with no other cause
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$40 – $130
Labor$80 – $160
Downstream oxygen sensor replacement (bank 1 sensor 2). National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P013A ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Watch the sensor's switching speed on a scan tool - a lazy sensor flatlines instead of waving.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →