P0136: O2 sensor circuit malfunction, bank 1 sensor 2
DIY difficulty 2/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Drive safeEmissions and fuel-economy issue. Safe to drive - fix when convenient, but don't ignore it forever.
Can I drive with P0136?
Can I drive with a P0136 code?
Yes. P0136 doesn't make your car unsafe to drive on its own. Emissions and fuel-economy issue. Safe to drive - fix when convenient, but don't ignore it forever. Fix it when convenient rather than putting it off indefinitely — even a minor fault can turn into a bigger bill if the underlying cause gets worse.
How serious is P0136?
Low. WrenchFair rates this one “Drive safe” — the least serious of its three driveability ratings. It's a fix-on-your-schedule fault, not a same-day emergency. Emissions and fuel-economy issue. Safe to drive - fix when convenient, but don't ignore it forever.
Will P0136 go away on its own?
The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.
The second oxygen sensor, the one that checks whether your catalytic converter is doing its job, has an electrical fault. The car drives fine, but you won't pass an emissions inspection.
VW/Audi note (VCDS): At steady cruise the downstream sensor should be nearly flat while the upstream oscillates; if both oscillate together, suspect the catalytic converter.
Model notes: Because this sensor only monitors the catalyst, the car drives normally with this code - but you will fail an emissions inspection, and a dead downstream sensor can mask a failing converter.
Key facts
P0136 means o2 sensor circuit malfunction, bank 1 sensor 2. The second oxygen sensor, the one that checks whether your catalytic converter is doing its job, has an electrical fault. The car drives fine, but you won't pass an emissions inspection. WrenchFair's published fair-price range for this repair is $40–$130 parts and $75–$180 labor at independent shops.
WrenchFair rates P0136 a 2-of-5 DIY difficulty (“Easiest O2 sensor to replace - downstream sensors see less heat and usually come out without a fight.”) with a “Drive safe” driveability rating: Emissions and fuel-economy issue. Safe to drive - fix when convenient, but don't ignore it forever. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light
failed emissions test
usually no drivability symptoms
poor fuel mileage
possible misfire
Likely causes
Failed downstream O2 sensor (most common)
Damaged wiring or corroded connector
Blown heater fuse
Exhaust leak between the sensor and the catalytic converter skewing readings
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 3 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check heater fuse and wiring before replacing Tests: Blown heater fuse
Watch live data: the downstream sensor should hold a fairly steady voltage around 0.5-0.8V at cruise; erratic readings suggest wiring or a failing catalyst Tests: Failed downstream O2 sensor (most common)
If the downstream sensor mirrors the upstream sensor's rapid switching, the catalytic converter itself is suspect, not the sensor Tests: Exhaust leak between the sensor and the catalytic converter skewing readings
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$40 – $130
Labor$75 – $180
O2 sensor replacement is the typical fix. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0136 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Easiest O2 sensor to replace - downstream sensors see less heat and usually come out without a fight.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →