P0114

P0114: Intake air temperature sensor 1 circuit intermittent

DIY difficulty 2/5

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.

Can I drive with P0114?

Can I drive with a P0114 code?

Short trips and gentle driving only, until you know the cause. Intermittent bad data confuses fueling - fix it before it causes a drivability complaint. If the check-engine light starts flashing, the engine shakes badly, or the car loses significant power, pull over safely and have it towed.

How serious is P0114?

Moderate. WrenchFair rates this one “Diagnose soon” — the car can usually get you home, but driving on it can turn a cheap fix into an expensive one. Intermittent bad data confuses fueling - fix it before it causes a drivability complaint.

Will P0114 go away on its own?

The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.

Your main intake-air temperature sensor cuts in and out - usually a loose connector. Expect intermittent rough running.

Model notes: On many vehicles the IAT sensor is built into the MAF sensor - an internal IAT fault means replacing the whole MAF assembly.

Key facts

Symptoms

Likely causes

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 4 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. Wiggle-test the IAT/MAF connector and harness while monitoring the temperature reading Tests: Loose or corroded IAT/MAF connector (most common)
  2. Inspect connector pins for spread or corrosion Tests: Loose or corroded IAT/MAF connector (most common)
  3. Check harness routing for chafing
  4. Replace the sensor (or MAF assembly if integrated) if the dropout is internal Tests: IAT sensor with an intermittent internal fault

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Typical price range

Parts$20 – $250
Labor$80 – $200

IAT sensor or connector repair (MAF assembly if integrated). National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0114 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

2 of 5 — Wiggle-test while watching IAT on a scan tool; the sensor is often part of the MAF assembly.

Watch this repair on YouTube

Parts & tools

Sensor replacement toolkit — what the job actually takes

Torque specs: Sensor mounting bolts: typically 8–12 Nm — verify spec. Never overtighten sensors with plastic bodies.

Pro tip: Check wiring and connectors first — chafed wires and corroded pins cause more sensor codes than dead sensors do.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →