P0022: Intake camshaft timing over-retarded, bank 2
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
DIY difficulty 2/5
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0022 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
Diagnose soonPerformance suffers and a stretched chain can jump teeth - get it checked rather than ignoring it.
Can I drive with P0022?
Can I drive with a P0022 code?
Short trips and gentle driving only, until you know the cause. Performance suffers and a stretched chain can jump teeth - get it checked rather than ignoring it. If the check-engine light starts flashing, the engine shakes badly, or the car loses significant power, pull over safely and have it towed.
How serious is P0022?
Moderate. WrenchFair rates this one “Diagnose soon” — the car can usually get you home, but driving on it can turn a cheap fix into an expensive one. Performance suffers and a stretched chain can jump teeth - get it checked rather than ignoring it.
Will P0022 go away on its own?
The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.
Your intake camshaft timing can't advance when the computer asks it to on the bank-2 side. Usually an oil-flow problem in the variable valve timing system or a worn timing chain.
Model notes: Platform patterns: Ford 5.4L 3V - tensioner-gasket oil bleed (watch hot-idle oil pressure; ~25 psi or lower starves the phaser); GM 2.4L Ecotec - chain guides and tensioners; Toyota - check oil condition, then the oil control valve.
Key facts
P0022 means intake camshaft timing over-retarded, bank 2. Your intake camshaft timing can't advance when the computer asks it to on the bank-2 side. Usually an oil-flow problem in the variable valve timing system or a worn timing chain. WrenchFair's published fair-price range for this repair is $40–$250 parts and $80–$2500 labor at independent shops.
WrenchFair rates P0022 a 2-of-5 DIY difficulty (“Oil service first; solenoid replacement is easy. Timing-chain diagnosis is the deeper end of this code.”) with a “Diagnose soon” driveability rating: Performance suffers and a stretched chain can jump teeth - get it checked rather than ignoring it. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light
poor acceleration and lack of power
rough idle
decreased fuel economy
Likely causes
Low oil level or pressure starving the VVT phaser (most common)
Clogged VVT solenoid screen or stuck-closed oil control valve
Stretched timing chain
Dirty or wrong-viscosity oil
Worn camshaft phaser
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check oil level and condition; service with the correct viscosity, then clear and retest Tests: Dirty or wrong-viscosity oil
Watch commanded vs. actual bank 2 intake camshaft angle under acceleration Tests: Worn camshaft phaser
Remove the bank 2 intake VVT solenoid and inspect screens for sludge; clean or replace Tests: Clogged VVT solenoid screen or stuck-closed oil control valve
Check engine oil pressure on high-mileage engines Tests: Low oil level or pressure starving the VVT phaser (most common)
Evaluate timing-chain stretch and phaser wear if oil and solenoid are good
Typical price range
Parts$40 – $250
Labor$80 – $2500
Two paths, very different prices: VVT oil control valve (solenoid) — the part runs $20-$165, installed $200-$1,200 at an independent shop (buy OEM; cheap aftermarket solenoids are known to cause limp mode on some Toyotas); the timing-chain path — $700+ just to inspect at a dealer teardown, $3,000+ for the repair, which is mostly labor. The ranges above span both paths; match the tier to your situation. National-average estimate. Actual quotes vary by vehicle, region, and shop — get a local written estimate. Corrected 2026-10-09 against real-world price evidence (Phase 2 adversarial audit).
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →