P001F: A camshaft profile actuator circuit high, bank 2
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonValve-lift control is compromised - performance suffers and hydraulic faults shouldn't sit.
Can I drive with P001F?
Can I drive with a P001F code?
Short trips and gentle driving only, until you know the cause. Valve-lift control is compromised - performance suffers and hydraulic faults shouldn't sit. If the check-engine light starts flashing, the engine shakes badly, or the car loses significant power, pull over safely and have it towed.
How serious is P001F?
Moderate. WrenchFair rates this one “Diagnose soon” — the car can usually get you home, but driving on it can turn a cheap fix into an expensive one. Valve-lift control is compromised - performance suffers and hydraulic faults shouldn't sit.
Will P001F go away on its own?
The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.
The wire controlling your intake camshaft's valve-lift switcher on the bank-2 side is reading too much voltage - likely shorted to a power wire.
Key facts
P001F means a camshaft profile actuator circuit high, bank 2. The wire controlling your intake camshaft's valve-lift switcher on the bank-2 side is reading too much voltage - likely shorted to a power wire. WrenchFair's published fair-price range for this repair is $60–$250 parts and $100–$350 labor at independent shops.
WrenchFair rates P001F a 3-of-5 DIY difficulty (“Short-to-power diagnosis; factory wiring diagrams are near-mandatory for these systems.”) with a “Diagnose soon” driveability rating: Valve-lift control is compromised - performance suffers and hydraulic faults shouldn't sit. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light
low power
poor driveability
reduced fuel economy
Likely causes
Control wire shorted to battery voltage
Failed profile actuator solenoid
Damaged or corroded connector
ECM driver fault (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check oil level and condition first
With the key on and solenoid unplugged, check for battery voltage on the control wire where it shouldn't be Tests: Control wire shorted to battery voltage
Trace the harness for chafing against power feeds
Test solenoid winding resistance against factory spec Tests: Failed profile actuator solenoid
Inspect connectors for damage or corrosion
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$60 – $250
Labor$100 – $350
Camshaft profile actuator solenoid replacement or wiring repair. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P001F ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Short-to-power diagnosis; factory wiring diagrams are near-mandatory for these systems.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →