P001A: A camshaft profile actuator circuit open, bank 1
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonThe engine runs on its default valve profile - performance and economy suffer, and hydraulic issues shouldn't be neglected.
The electric valve that switches your intake camshaft's valve-lift profile on the cylinder-1 side has a broken circuit. You'll notice weaker performance and worse mileage.
Model notes: Seen on engines with variable valve lift (Audi valvelift, Porsche, Volvo, Hyundai, Fiat). 'A' is typically the intake camshaft; designs differ - verify against your engine's manual.
Key facts
P001A means a camshaft profile actuator circuit open, bank 1. The electric valve that switches your intake camshaft's valve-lift profile on the cylinder-1 side has a broken circuit. You'll notice weaker performance and worse mileage. WrenchFair's published fair-price range for this repair is $60–$250 parts and $100–$350 labor at independent shops.
WrenchFair rates P001A a 3-of-5 DIY difficulty (“Wiring diagnosis is standard multimeter work, but these variable-lift systems vary a lot by manufacturer - the factory manual is essential.”) with a “Diagnose soon” driveability rating: The engine runs on its default valve profile - performance and economy suffer, and hydraulic issues shouldn't be neglected. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light
low power
poor driveability
reduced fuel economy
abnormal throttle response
altered power delivery
Likely causes
Broken or damaged wiring in the profile actuator circuit (most common electrical cause)
Failed camshaft profile actuator solenoid
Corroded or loose connector
Low, dirty, or wrong-viscosity oil preventing hydraulic operation
ECM fault (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check oil level, condition, and viscosity first - service if suspect, since the system is oil-driven Tests: Low, dirty, or wrong-viscosity oil preventing hydraulic operation
Get the factory wiring diagram and locate the bank 1 A profile actuator solenoid and its harness Tests: Broken or damaged wiring in the profile actuator circuit (most common electrical cause)
Inspect the harness and connectors for damage, chafing, loose pins, or oil intrusion; use contact cleaner on the pins Tests: Corroded or loose connector
Unplug the solenoid and test its winding for an open against factory spec Tests: Failed camshaft profile actuator solenoid
Check circuit continuity back to the ECM
Clear the code and verify the profile switch operates with a bi-directional scan tool if available
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$60 – $250
Labor$100 – $350
Camshaft profile actuator solenoid replacement or wiring repair. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P001A ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Wiring diagnosis is standard multimeter work, but these variable-lift systems vary a lot by manufacturer - the factory manual is essential.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →