Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonAddress soon - sluggish cam timing degrades performance and can hide a wearing timing chain.
Can I drive with P000C?
Can I drive with a P000C code?
Short trips and gentle driving only, until you know the cause. Address soon - sluggish cam timing degrades performance and can hide a wearing timing chain. If the check-engine light starts flashing, the engine shakes badly, or the car loses significant power, pull over safely and have it towed.
How serious is P000C?
Moderate. WrenchFair rates this one “Diagnose soon” — the car can usually get you home, but driving on it can turn a cheap fix into an expensive one. Address soon - sluggish cam timing degrades performance and can hide a wearing timing chain.
Will P000C go away on its own?
The warning light can turn off by itself after clean drive cycles, but the code stays stored in the computer's memory and the fault is still there. Clearing it without fixing the cause just buys time — it will come back when the computer re-runs the self-test. Exception: a loose gas cap — tighten it and drive a few days.
The gadget adjusting your intake camshaft timing on the bank-2 side is reacting too slowly - usually dirty or low engine oil gumming up the variable valve timing system.
Model notes: 'A' is usually the intake camshaft; bank 2 is the side opposite cylinder 1.
Key facts
P000C means a camshaft position slow response bank 2. The gadget adjusting your intake camshaft timing on the bank-2 side is reacting too slowly - usually dirty or low engine oil gumming up the variable valve timing system. WrenchFair's published fair-price range for this repair is $40–$250 parts and $80–$300 labor at independent shops.
WrenchFair rates P000C a 2-of-5 DIY difficulty (“An oil change is the legitimate first step; the solenoid is usually an accessible bolt-on part.”) with a “Diagnose soon” driveability rating: Address soon - sluggish cam timing degrades performance and can hide a wearing timing chain. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light
rough idle
poor acceleration
decreased fuel economy
increased emissions
Likely causes
Dirty, degraded, or low engine oil restricting flow to the VVT system (most common)
Clogged or sticking VVT oil control valve (solenoid) for bank 2 intake
Worn camshaft phaser
Stretched timing chain
Faulty camshaft position sensor or damaged wiring
PCM fault (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Check oil level and condition - change oil and filter if overdue or wrong viscosity, then clear and retest
Watch commanded vs. actual bank 2 intake camshaft angle on the scan tool during throttle snaps Tests: Clogged or sticking VVT oil control valve (solenoid) for bank 2 intake
Inspect and clean or replace the bank 2 intake VVT oil control valve and its screen Tests: Clogged or sticking VVT oil control valve (solenoid) for bank 2 intake
Check the camshaft position sensor wiring and connector Tests: Faulty camshaft position sensor or damaged wiring
If still slow, evaluate the phaser and timing chain for wear
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$40 – $250
Labor$80 – $300
Engine oil change or VVT oil control valve (solenoid) replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P000C ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — An oil change is the legitimate first step; the solenoid is usually an accessible bolt-on part.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →