Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonA shorted fuel-control circuit can strand you with a no-start - diagnose before it leaves you somewhere inconvenient.
The wiring to your fuel-pressure control valve is shorted to ground. The computer can't control fuel pressure properly, which can cause starting trouble or limp mode.
Key facts
P0003 means fuel volume regulator control circuit low. The wiring to your fuel-pressure control valve is shorted to ground. The computer can't control fuel pressure properly, which can cause starting trouble or limp mode. WrenchFair's published fair-price range for this repair is $60–$300 parts and $120–$350 labor at independent shops.
WrenchFair rates P0003 a 3-of-5 DIY difficulty (“Finding a short to ground takes patience with a multimeter, and the regulator is mounted on a high-pressure fuel system.”) with a “Diagnose soon” driveability rating: A shorted fuel-control circuit can strand you with a no-start - diagnose before it leaves you somewhere inconvenient. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
check engine light
hard start or no start
limp mode with reduced power
rough running
Likely causes
Wiring shorted to ground in the regulator control circuit (chafed harness touching the engine or frame)
Shorted fuel volume regulator solenoid winding
Corroded connector with terminals bridged by moisture or debris
Failed PCM driver holding the circuit low (rare)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Unplug the fuel volume regulator and clear the code - if it returns with the regulator unplugged, the short is in the harness, not the part Tests: Shorted fuel volume regulator solenoid winding
With the regulator unplugged, check the control wire for continuity to ground; repair any chafed or pinched section Tests: Wiring shorted to ground in the regulator control circuit (chafed harness touching the…
Measure the regulator solenoid resistance against factory spec - a near-zero reading means a shorted winding Tests: Shorted fuel volume regulator solenoid winding
Inspect connectors for corrosion or water intrusion that could bridge terminals to ground Tests: Corroded connector with terminals bridged by moisture or debris
If harness and regulator both test good, suspect the PCM driver circuit
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$60 – $300
Labor$120 – $350
Wiring harness repair or fuel volume regulator replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for P0003 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Finding a short to ground takes patience with a multimeter, and the regulator is mounted on a high-pressure fuel system.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →