Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonYour regular brakes work fine, but stability control is off. Fix the underlying sensor or calibration issue - don't replace the module first.
Your stability control computer did a cross-check of all its sensors and the numbers don't agree. Your normal brakes work fine, but stability control is switched off until the disagreement is found.
Key facts
C0287 means eSP Performance. Your stability control computer did a cross-check of all its sensors and the numbers don't agree. Your normal brakes work fine, but stability control is switched off until the disagreement is found. WrenchFair's published fair-price range for this repair is $0–$300 parts and $80–$250 labor at independent shops.
WrenchFair rates C0287 a 4-of-5 DIY difficulty (“The fix is usually calibration or another sensor code - both DIY-friendly with the right scan tool.”) with a “Diagnose soon” driveability rating: Your regular brakes work fine, but stability control is off. Fix the underlying sensor or calibration issue - don't replace the module first. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
stability control warning light on
abs warning light on
stability control intervenes at odd times or not at all
Likely causes
a sensor calibration needed after an alignment or suspension repair (most common)
fix any wheel speed, steering angle, or yaw sensor codes first - they feed this check
sensor cluster loose or mounted incorrectly
a drifting yaw rate or lateral acceleration sensor
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
1. Scan every module and fix any wheel speed, steering angle, yaw rate, or lateral acceleration codes first - they usually explain this one. Tests: fix any wheel speed, steering angle, or yaw sensor codes first - they feed this check
2. Check for recent alignment, suspension, or collision work that needs a sensor recalibration. Tests: a sensor calibration needed after an alignment or suspension repair (most common)
3. Verify the yaw/lateral-acceleration sensor cluster is mounted tightly and correctly. Tests: sensor cluster loose or mounted incorrectly
4. Run the stability sensor calibration or zero-point learn procedure. Tests: a sensor calibration needed after an alignment or suspension repair (most common)
5. If it still fails with all sensors reading correctly, the module itself is suspect.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$0 – $300
Labor$80 – $250
Often just a calibration or another sensor's repair ($0-$300). A module replacement runs $700-$1,400 installed. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for C0287 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
4 of 5 — The fix is usually calibration or another sensor code - both DIY-friendly with the right scan tool.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →