Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonYour regular brakes keep working normally, but ABS, traction control, and stability control are probably disabled until this is fixed. Drive gently on wet or slippery roads.
Your car's ABS computer tried to work a brake valve inside the hydraulic control unit and it didn't respond correctly. Your normal brakes work fine, but ABS, traction control, and stability control are likely switched off.
Key facts
C0146 means left Front ABS Outlet Solenoid Circuit. Your car's ABS computer tried to work a brake valve inside the hydraulic control unit and it didn't respond correctly. Your normal brakes work fine, but ABS, traction control, and stability control are likely switched off. WrenchFair's published fair-price range for this repair is $400–$1400 parts and $300–$700 labor at independent shops.
WrenchFair rates C0146 a 5-of-5 DIY difficulty (“Diagnosis is DIY-friendly, but the repair usually means a remanufactured hydraulic unit and a proper brake bleed.”) with a “Diagnose soon” driveability rating: Your regular brakes keep working normally, but ABS, traction control, and stability control are probably disabled until this is fixed. Drive gently on wet or slippery roads. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
abs warning light on
traction control or stability control light on
cruise control stops working
Likely causes
valve coil failed inside the hydraulic control unit
valve stuck from old or contaminated brake fluid
wiring fault between the module and the hydraulic unit
internal ABS module fault - rule out fluid condition and wiring first
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
1. Clear the code and re-scan after a short drive to confirm it is a hard fault, not a one-time glitch.
2. Check the brake fluid: dark, murky fluid is a classic cause of sticky valves. A full fluid flush is the cheapest first move. Tests: valve stuck from old or contaminated brake fluid
3. With a scan tool that has ABS bidirectional controls, try commanding the outlet solenoid on and off and listen/feel for a click. Tests: valve coil failed inside the hydraulic control unit
4. Inspect the wiring and connector at the hydraulic control unit for corrosion or damage. Tests: valve coil failed inside the hydraulic control unit
5. If the valve still won't respond, the fix is usually a remanufactured hydraulic control unit followed by a full brake bleed.
6. After replacement, bleed the brakes thoroughly and clear all ABS codes before the test drive.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$400 – $1400
Labor$300 – $700
A remanufactured hydraulic control unit with installation and brake bleed, roughly $800-$1,800 all-in. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for C0146 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
5 of 5 — Diagnosis is DIY-friendly, but the repair usually means a remanufactured hydraulic unit and a proper brake bleed.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →