C0038

C0038 on a 2010–2014 Volkswagen Golf/GTI: Left Rear Wheel Speed Sensor Supply

Print shop one-pager Take this page to the shop — causes, fair prices, and sharp questions on one sheet.
For your specific vehicle: C0038 on a 2011–2018 Porsche Cayenne · 2010–2014 Volkswagen Golf/GTI · 2015–2021 Volkswagen Golf/GTI

DIY difficulty 4/5

The ABS computer can't power the left rear wheel speed sensor properly, so the sensor can't send a clean signal. Your normal brakes work fine, but ABS and traction control may be disabled.

Key facts

☑ Before you buy parts — check these first:
On your 2010–2014 Volkswagen Golf/GTI (2.0T TSI EA888 gen1/2 (CCTA/CBFA)) — Front brake pads & rotors: Community-reported
Standard floating-caliper front brakes (312mm rotors). Remove the caliper anti-rattle spring with a flathead, then the guide pins (T45 per the main golfmk6 thread; some owners report 7mm allen on their cars — check before buying tools). Hang the caliper with a bungee or coat hanger so it never dangles by the hose. The rotor is held by a T30 set screw; the caliper carrier takes a 21mm socket (rotors only). The inboard pad on the front-left carries the wear sensor — transfer its cable to the new pad.
Do this test first: 1. Clear the code, drive above about 15 mph, and re-scan. Only spend money if the code comes back.
→ Passes: that cause is ruled out — run the next test in the diagnostic path below.
→ Fails: fix what failed — that’s your cause. Clear the code and re-test before buying anything else.
No owner fix reports yet for C0038 on the 2010–2014 Volkswagen Golf/GTI — but the community-sourced Front brake pads & rotors note above covers an owner-reported fix.
Fixed yours? Report it — you'll help the next owner.

Torque specs

Tips

Sources: golfmk6: brake tools and torque specs (front 140 ft-lb carrier, T45 guide pins 18 ft-lb)

Typical difficulty: Moderate — based on 265 code guides for the brake repair area (an area-level estimate, not this exact job).

How notes are verified: Robbie-tested — Robbie did this repair on his own car and confirmed the fix himself. Owner-verified — community repair procedure with 2+ cited sources. Factory-documented — drawn from a factory TSB, recall, or campaign document; a factory procedure, not an owner-tested fix. Community-reported — single-source or otherwise unverified; treat as a lead, not a verdict.

No owner reports yet

Symptoms

Likely causes

What usually pays the bill on this car, most common first — but work the diagnostic path above cheapest-first. Test order and bill order aren’t the same thing.

Owner notes linked to C0038: 3 across 1 repair — these are counts of owner-written notes, not odds of fixing your car.

Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →

Before you buy the part — 6 checks

Work these checks before spending money — each one rules a cause in or out, cheapest first.

  1. 1. Clear the code, drive above about 15 mph, and re-scan. Only spend money if the code comes back.
  2. 2. Watch the left rear wheel speed in ABS live data at low speed. A dead, jumpy, or mismatched reading confirms the problem corner. Tests: failed wheel speed sensor
  3. 3. Unplug the left rear sensor and inspect the connector for corrosion, moisture, or bent pins. Tests: corroded sensor connector
  4. 4. Check the sensor supply voltage at the left rear connector with the ignition on, then check the harness back toward the module for opens or shorts. Tests: corroded sensor connector
  5. 5. Trace the sensor harness along the wheel-arch flex point and look for chafing or breaks.
  6. 6. If the wiring and tone ring check out, replace the left rear wheel speed sensor — it is the most common fix.

No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.

Most likely job on your 2010–2014 Volkswagen Golf/GTI: Front brake pads & rotors — test first, then buy for this job.

Expensive fork: Brake caliper — if a wheel drags or overheats after fresh pads and rotors. The price range below is a national planning range for C0038 on this vehicle — not a quote: it spans the common job at the low end to the expensive fork at the high end. 0 owner invoices on this generation — treat these as planning numbers.
If a shop quote lands near the top of the range, that’s fork money, not the common job — ask which test failed before authorizing it.

Typical price range

Parts$40 – $180
Labor$90 – $250

A wiring repair on the wheel speed sensor supply circuit, roughly $150-$350 at a shop. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.

Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.

Got a shop quote? Grade it →

What will this cost to fix? A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for C0038 ranked, each with a price range.
They handed you a printout at the parts store? Decode it before you buy.

DIY difficulty

4 of 5 — Sensor and harness work with basic hand tools; seized sensors and corroded connectors are the usual fights.

Watch this repair on YouTube

Parts & tools

ABS / wheel-speed toolkit — what the job actually takes

Torque specs: Wheel-speed sensor bolts: typically 8–12 Nm. (Caliper bracket bolts are far tighter — 90–140 Nm — don’t confuse them.)

Pro tip: Inspect the tone ring/reluctor for cracks and debris first — the sensor itself is often innocent.

As an Amazon Associate, WrenchFair earns from qualifying purchases.

Related codes

Check another code
Got a quote?Grade it →Shop one-pagerPrint it →Another code?Look it up →
Who's behind this guide? WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes. Read the full methodology →