B00B0: Driver seat occupant classification sensor A circuit fault
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonThe car drives normally, but the affected restraint may not protect you in a crash - get it diagnosed promptly.
Your car's airbag computer found an electrical problem in a driver's seat sensor that reports how much weight is on that corner of the seat cushion. The airbag warning light will stay on, and the airbags may deploy at a default (less tailored) force until it is fixed. The car still drives normally.
Key facts
B00B0 means driver seat occupant classification sensor A circuit fault. Your car's airbag computer found an electrical problem in a driver's seat sensor that reports how much weight is on that corner of the seat cushion. The airbag warning light will stay on, and the airbags may deploy at a default (less tailored) force until it is fixed. The car still drives normally. WrenchFair's published fair-price range for this repair is $50–$250 parts and $100–$300 labor at independent shops.
WrenchFair rates B00B0 a 3-of-5 DIY difficulty (“Under-seat access is basic hand-tool work, but the sensor may need a scan-tool calibration afterward.”) with a “Diagnose soon” driveability rating: The car drives normally, but the affected restraint may not protect you in a crash - get it diagnosed promptly. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
airbag warning light on
passenger airbag off light behaving incorrectly
Likely causes
Damaged occupant classification sensor A in the driver's seat (most common)
Wiring under the seat damaged - kicked, pinched by the seat track, or corroded connector
Connector under the seat disturbed by moving the seat or cleaning
Sensor needs recalibration after seat removal or replacement
Restraints control module fault (rare - diagnose everything else first)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Disconnect the battery (negative terminal first) and wait at least 10 minutes before touching any SRS connector or component. Tests: Wiring under the seat damaged - kicked, pinched by the seat track, or corroded connector
Read the code with an SRS-capable scan tool and note any subcode digits after the main code (e.g. -11, -12, -13) - many makes append them to say open circuit, short to ground, short to battery, or wires shorted together.
With power still off, inspect the driver's under-seat wiring and connectors - slide the seat fully forward and back and look for pinching, chafing, loose plugs, or corrosion. Tests: Wiring under the seat damaged - kicked, pinched by the seat track, or corroded connector
Test the occupant classification sensor A per the factory service manual; replace it if it tests bad. Tests: Damaged occupant classification sensor A in the driver's seat (most common)
After replacement, perform any calibration or reset the service manual calls for with an SRS-capable scan tool.
Verify the restraints control module's power and ground feeds, repair the fault, reconnect the battery, clear the code, and confirm the airbag light completes its power-on self-test.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$50 – $250
Labor$100 – $300
Occupant classification sensor A replacement, including any required calibration. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for B00B0 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — Under-seat access is basic hand-tool work, but the sensor may need a scan-tool calibration afterward.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →