B0092: Left side restraints sensor 2 circuit fault
DIY difficulty 2/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonThe car drives normally, but the affected restraint may not protect you in a crash - get it diagnosed promptly.
Your car's airbag computer lost reliable contact with one of its crash sensors - the left side impact sensor 2 that helps it detect a collision. The airbag warning light will stay on, and the airbags tied to that sensor may not deploy correctly in a crash. The car still drives normally.
Key facts
B0092 means left side restraints sensor 2 circuit fault. Your car's airbag computer lost reliable contact with one of its crash sensors - the left side impact sensor 2 that helps it detect a collision. The airbag warning light will stay on, and the airbags tied to that sensor may not deploy correctly in a crash. The car still drives normally. WrenchFair's published fair-price range for this repair is $50–$150 parts and $100–$250 labor at independent shops.
WrenchFair rates B0092 a 2-of-5 DIY difficulty (“Impact sensors are small bolt-on units; the work is locating them per the service manual and inspecting wiring and mounts with basic hand tools.”) with a “Diagnose soon” driveability rating: The car drives normally, but the affected restraint may not protect you in a crash - get it diagnosed promptly. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
airbag warning light on
srs service message on the dash
Likely causes
Damaged left side impact sensor 2 impact sensor or mounting (most common after any bump to that area - even a hard parking-lot hit)
Cut, chafed, or corroded wiring to the sensor
Loose or corroded sensor connector
Failed sensor internally
Restraints control module fault (rare - diagnose everything else first)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Disconnect the battery (negative terminal first) and wait at least 10 minutes before touching any SRS connector or component. Tests: Loose or corroded sensor connector
Read the code with an SRS-capable scan tool and note any subcode digits after the main code (e.g. -11, -12, -13) - many makes append them to say open circuit, short to ground, short to battery, or wires shorted together.
With power still off, locate the sensor (in the left C-pillar or rear door/sill area - confirm the exact spot in your model's service information) and inspect it for impact damage, a bent bracket, or a loose mount. Tests: Damaged left side impact sensor 2 impact sensor or mounting (most common after any bump…
Inspect the sensor's wiring and connector for cuts, chafing, moisture, and corrosion; repair the harness as needed. Tests: Loose or corroded sensor connector
Replace the sensor if it is damaged or tests bad, securing it exactly as the service manual shows.
Verify the restraints control module's power and ground feeds, repair the fault, reconnect the battery, clear the code, and confirm the airbag light completes its power-on self-test.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$50 – $150
Labor$100 – $250
Impact sensor replacement, or wiring/connector repair to the sensor. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for B0092 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
2 of 5 — Impact sensors are small bolt-on units; the work is locating them per the service manual and inspecting wiring and mounts with basic hand tools.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →