Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonThe car drives normally, but the affected restraint may not protect you in a crash - get it diagnosed promptly.
Your car's airbag computer found a problem with the system that senses where the occupant is sitting relative to the airbag. The airbag warning light will stay on, and the passenger airbag may stay off or deploy at reduced force until it is fixed. The car still drives normally.
Key facts
B00A1 means occupant position system fault. Your car's airbag computer found a problem with the system that senses where the occupant is sitting relative to the airbag. The airbag warning light will stay on, and the passenger airbag may stay off or deploy at reduced force until it is fixed. The car still drives normally. WrenchFair's published fair-price range for this repair is $250–$700 parts and $150–$350 labor at independent shops.
WrenchFair rates B00A1 a 3-of-5 DIY difficulty (“The mat itself swaps with hand tools, but the system usually needs a scan-tool calibration afterward - which is the part many DIYers hand to a shop.”) with a “Diagnose soon” driveability rating: The car drives normally, but the affected restraint may not protect you in a crash - get it diagnosed promptly. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
airbag warning light on
passenger airbag off light stuck on with an adult seated
passenger airbag off light stuck off with the seat empty
Likely causes
Damaged occupant position system sensor or mat in the passenger seat (most common - cracked from heavy loads, age, or a knee in the seat)
Connector under the passenger seat disturbed, loose, or corroded
Spilled liquid soaking into the seat sensor
System needs recalibration after seat removal, seat work, or part replacement
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 7 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Disconnect the battery (negative terminal first) and wait at least 10 minutes before touching any SRS connector or component. Tests: Connector under the passenger seat disturbed, loose, or corroded
Read the code with an SRS-capable scan tool and note any subcode digits after the main code (e.g. -11, -12, -13) - many makes append them to say open circuit, short to ground, short to battery, or wires shorted together.
With power still off, inspect the under-seat connectors - look for loose plugs, bent pins, corrosion, and signs of liquid spills. Tests: Connector under the passenger seat disturbed, loose, or corroded
Check for aftermarket seat covers, seat heaters, or heavy objects on the seat that can confuse the system; remove them and retest. Tests: Damaged occupant position system sensor or mat in the passenger seat (most common -…
Test the sensor/mat per the factory service manual; replace it if damaged.
After any replacement or seat removal, perform the occupant classification calibration/reset with an SRS-capable scan tool.
Verify the restraints control module's power and ground feeds, repair the fault, reconnect the battery, clear the code, and confirm the airbag light completes its power-on self-test.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$250 – $700
Labor$150 – $350
Occupant classification sensor mat replacement, including calibration. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for B00A1 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — The mat itself swaps with hand tools, but the system usually needs a scan-tool calibration afterward - which is the part many DIYers hand to a shop.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →