Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonThe car drives normally, but the affected restraint may not protect you in a crash - get it diagnosed promptly.
Your car's airbag computer found a problem with its rollover sensor - the part that detects if the car is tipping over so it can fire the curtain airbags. The airbag warning light will stay on, and rollover protection may not work in a crash. The car still drives normally.
Key facts
B0099 means rollover sensor circuit fault. Your car's airbag computer found a problem with its rollover sensor - the part that detects if the car is tipping over so it can fire the curtain airbags. The airbag warning light will stay on, and rollover protection may not work in a crash. The car still drives normally. WrenchFair's published fair-price range for this repair is $150–$500 parts and $150–$300 labor at independent shops.
WrenchFair rates B0099 a 3-of-5 DIY difficulty (“The sensor is often inside the restraints module itself, so this code frequently ends in module replacement and programming at a shop.”) with a “Diagnose soon” driveability rating: The car drives normally, but the affected restraint may not protect you in a crash - get it diagnosed promptly. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
airbag warning light on
srs service message on the dash
Likely causes
Failed rollover sensor (most common - often internal to the restraints module)
Damaged wiring or corroded connector to a separately mounted sensor
Water intrusion under the center console corroding the sensor or module
Restraints control module fault (the sensor is part of the module on many vehicles)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 5 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Disconnect the battery (negative terminal first) and wait at least 10 minutes before touching any SRS connector or component. Tests: Damaged wiring or corroded connector to a separately mounted sensor
Read the code with an SRS-capable scan tool and note any subcode digits after the main code (e.g. -11, -12, -13) - many makes append them to say open circuit, short to ground, short to battery, or wires shorted together.
With power still off, check under the center console for water damage and inspect the sensor/module connectors for corrosion. Tests: Water intrusion under the center console corroding the sensor or module
Test the sensor circuit per the factory service manual; on many vehicles a failed rollover sensor means replacing the restraints control module. Tests: Restraints control module fault (the sensor is part of the module on many vehicles)
Verify the restraints control module's power and ground feeds, repair the fault, reconnect the battery, clear the code, and confirm the airbag light completes its power-on self-test.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$150 – $500
Labor$150 – $300
Rollover sensor or restraints control module replacement. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for B0099 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — The sensor is often inside the restraints module itself, so this code frequently ends in module replacement and programming at a shop.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →