B0080: Driver seatbelt load limiter deployment control circuit fault
DIY difficulty 3/5
Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonThe car drives normally, but the affected restraint may not protect you in a crash - get it diagnosed promptly.
Your car's airbag computer found an electrical problem in the driver's seatbelt's load limiter - the mechanism that lets the belt give a controlled amount in a crash to protect your chest. The airbag warning light will stay on. The belt still holds you normally in everyday driving.
Key facts
B0080 means driver seatbelt load limiter deployment control circuit fault. Your car's airbag computer found an electrical problem in the driver's seatbelt's load limiter - the mechanism that lets the belt give a controlled amount in a crash to protect your chest. The airbag warning light will stay on. The belt still holds you normally in everyday driving. WrenchFair's published fair-price range for this repair is $150–$450 parts and $150–$350 labor at independent shops.
WrenchFair rates B0080 a 3-of-5 DIY difficulty (“The load limiter lives inside the retractor; diagnosis is inspection and multimeter work after the mandatory battery disconnect, and replacement is a bolt-in job.”) with a “Diagnose soon” driveability rating: The car drives normally, but the affected restraint may not protect you in a crash - get it diagnosed promptly. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
airbag warning light on
srs service message on the dash
Likely causes
Damaged wiring or connector to the driver's retractor (most common - under-seat and pillar harnesses get disturbed)
Failed adaptive load limiter element in the driver's retractor
Corroded connector at the retractor
A previously deployed or damaged retractor that was never replaced - check crash history
Restraints control module fault (rare - diagnose everything else first)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Disconnect the battery (negative terminal first) and wait at least 10 minutes before touching any SRS connector or component. Tests: Damaged wiring or connector to the driver's retractor (most common - under-seat and…
Read the code with an SRS-capable scan tool and note any subcode digits after the main code (e.g. -11, -12, -13) - many makes append them to say open circuit, short to ground, short to battery, or wires shorted together.
With power still off, inspect the driver's retractor wiring and connectors (usually at the base of the B-pillar or under the seat) for damage, pinching, or corrosion. Tests: Damaged wiring or connector to the driver's retractor (most common - under-seat and…
Check for signs of prior deployment or crash damage to the retractor - a fired unit must be replaced. Tests: A previously deployed or damaged retractor that was never replaced - check crash history
Test the circuit only with the battery disconnected and only per the factory service manual's SRS procedure - never apply power to or probe a live deployment circuit.
Verify the restraints control module's power and ground feeds, repair the fault, reconnect the battery, clear the code, and confirm the airbag light completes its power-on self-test.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$150 – $450
Labor$150 – $350
Wiring/connector repair, or seatbelt retractor assembly replacement if the load limiter element failed. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for B0080 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — The load limiter lives inside the retractor; diagnosis is inspection and multimeter work after the mandatory battery disconnect, and replacement is a bolt-in job.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →