Print shop one-pagerTake this page to the shop — causes, fair prices, and sharp questions on one sheet.
Diagnose soonThe car drives normally, but the affected restraint may not protect you in a crash - get it diagnosed promptly.
Your car's airbag computer found an electrical problem in the driver's seatbelt's tension sensor - the part that senses how tight the belt is pulled. The airbag warning light will stay on, and the passenger airbag may default to a conservative (disabled or reduced-force) state. The belt itself still holds you normally.
Key facts
B0060 means driver seatbelt tension sensor circuit fault. Your car's airbag computer found an electrical problem in the driver's seatbelt's tension sensor - the part that senses how tight the belt is pulled. The airbag warning light will stay on, and the passenger airbag may default to a conservative (disabled or reduced-force) state. The belt itself still holds you normally. WrenchFair's published fair-price range for this repair is $120–$350 parts and $150–$300 labor at independent shops.
WrenchFair rates B0060 a 3-of-5 DIY difficulty (“The sensor is part of the buckle or anchor assembly; replacement is hand-tool work but may require a scan-tool calibration afterward.”) with a “Diagnose soon” driveability rating: The car drives normally, but the affected restraint may not protect you in a crash - get it diagnosed promptly. These are this guide’s own published ratings.
For labor context, WrenchFair's methodology page cites two published numbers: about half of US independent shops charge $120–$159/hr (PartsTech survey of 752 shops, fall 2024), and the national average posted mechanical rate was $163/hr in June 2026 (NABR LaborRateHero). Multiply either band by a quote's labor hours to judge whether its labor line is in range.
Symptoms
airbag warning light on
passenger airbag off light stuck on or off incorrectly
Likely causes
Failed tension sensor in the driver's belt buckle or anchor (most common)
Damaged wiring under the seat - kicked, pinched by the seat track, or corroded connector
System needs recalibration after seat removal or belt work
Restraints control module fault (rare - diagnose everything else first)
Too many suspects? Answer 4–6 quick questions and this page's published cause list re-orders itself for your situation — plus the cheapest test to run next. Start the elimination wizard →
Before you buy the part — 6 checks
Work these checks before spending money — each one rules a cause in or out, cheapest first.
Disconnect the battery (negative terminal first) and wait at least 10 minutes before touching any SRS connector or component. Tests: Damaged wiring under the seat - kicked, pinched by the seat track, or corroded connector
Read the code with an SRS-capable scan tool and note any subcode digits after the main code (e.g. -11, -12, -13) - many makes append them to say open circuit, short to ground, short to battery, or wires shorted together.
With power still off, inspect the driver's belt anchor/buckle wiring under the seat for damage, pinching, or corrosion. Tests: Failed tension sensor in the driver's belt buckle or anchor (most common)
Test the tension sensor per the factory service manual; replace the buckle/anchor assembly if the sensor is bad. Tests: Failed tension sensor in the driver's belt buckle or anchor (most common)
After any replacement, perform the sensor calibration/reset with an SRS-capable scan tool if the service manual calls for it.
Verify the restraints control module's power and ground feeds, repair the fault, reconnect the battery, clear the code, and confirm the airbag light completes its power-on self-test.
No scan tool yet? The Veepeak OBDCheck (~$32) reads and clears codes from your phone in about two minutes.
Typical price range
Parts$120 – $350
Labor$150 – $300
Seatbelt buckle/anchor assembly replacement, including any required sensor calibration. National-average estimate for the most common repair for this code. Actual quotes vary by vehicle, region, and shop - get a local written estimate.
Dealer vs independent shop: these ranges reflect typical independent-shop prices. A dealer will usually quote higher — higher labor rates plus OEM-only parts — so a dealer quote at the top of (or a bit above) this range isn't automatically a rip-off. For a big dealer number, get a second quote from an independent shop before authorizing the work.
What will this cost to fix?A code doesn’t name the repair — run the code-first estimator to see the most likely fixes for B0060 ranked, each with a price range. They handed you a printout at the parts store? Decode it before you buy.
DIY difficulty
3 of 5 — The sensor is part of the buckle or anchor assembly; replacement is hand-tool work but may require a scan-tool calibration afterward.
Who's behind this guide?WrenchFair is built by a fellow DIYer, not a repair shop. Code meanings follow the SAE J2012 standard; cause rankings come from real-world repair evidence (service bulletins, owner reports, NHTSA records); prices are typical US ranges, not quotes.Read the full methodology →